What you need
- A submersible utility or sump pump. Many homeowners use a 1/4 or 1/3 horsepower model, and a float switch is a useful feature.
- A discharge hose long enough to reach your drainage point, such as a backwash hose or heavy-duty layflat hose.
- A hose clamp or the correct adapter to connect the hose to the pump outlet.
- A rope or similar to lower and move the pump. Never lift or drag a pump by its power cord.
- A GFCI-protected outlet, or a portable GFCI device, and a suitable outdoor-rated extension cord if needed.
- A wet/dry vacuum or sponges for the last bit of water.
Before you start
- Plan the discharge. Decide where the water goes and check your local rules. Some areas require a sewer cleanout, and some limit storm drain use. Our pool draining guide explains the options.
- Let the chlorine drop. Stop adding chemicals beforehand and test the water, especially if you plan to put it on the lawn. See whether pool water kills grass.
- Check the weather. Avoid draining during or just after heavy rain, and avoid extreme heat, which is hard on liners and plaster.
- Think about groundwater. If you have an inground pool, read about hydrostatic pressure before taking out all the water. For fiberglass, see draining a fiberglass pool.
- Turn off the pool equipment. Switch off the main pump, heater, salt system and automation timers, so nothing starts up while the water is low.
Step by step
- Connect the hose. Attach the discharge hose to the pump outlet with a clamp or screw-on fitting, and check it is tight.
- Lay out the hose. Run it to the discharge point, downhill if possible, with no kinks. Weight or secure the end so it does not whip around.
- Lower the pump. Tie a rope to the pump handle and lower it into the deepest part of the pool, or to the shallow end if you are only lowering the level a little. Make sure it sits flat and stable. Do not stand in the pool while the pump runs.
- Plug in. Plug the pump’s power cord into a GFCI-protected outlet. Keep the plug and any extension cord connection dry and off the ground where water can pool.
- Switch on. Confirm water is flowing out of the far end of the hose.
- Monitor. Stay nearby. Check the discharge, the hose connections and the surrounding ground, to see that the water is not pooling near your house or the pool.
- Move the pump as needed. Once the shallow end is empty, shift the pump toward the deep end using the rope.
Handling the last inches
A submersible pump cannot remove every bit of water. Once the level gets close to the pump’s intake, the flow slows. Some pumps have automatic shut-off, but many keep running and can overheat if they run dry, so unplug them once the water stops flowing.
For the remainder you can:
- use a wet/dry vacuum;
- use a low-profile pump designed to get closer to the floor;
- sweep the water toward the drain or a low point and soak it up with sponges or towels.
You usually do not need to remove every drop, unless you are doing a repair or cleaning job that calls for it.
Electrical safety
Water and electricity are a dangerous mix, so take this part seriously:
- Always use a GFCI outlet or a portable GFCI or RCD device.
- Never carry or hang the pump by its cord.
- Keep people and pets out of the pool while the pump is plugged in.
- Use extension cords rated for outdoor use, and keep connections out of puddles.
- Unplug the pump before you touch it or move it by hand.
- If anything seems wrong, such as tripping breakers or a damaged cord, stop and ask a qualified electrician.
Choosing a pump
- Flow rate: bigger pumps drain faster. Pumps are often rated in gallons per hour at a given height, so compare the figures at the lift you need.
- Hose size: a larger hose outlet reduces friction and speeds the job.
- Float switch: useful for protecting the motor, but not a substitute for watching the job.
- Rent or buy: if you only drain once in a few years, renting can make sense, while buying suits people who drain often or use it for storms and basements.
Larger pools can take many hours to a day or more to drain, depending on the pump, hose length and lift.
Common mistakes
- Running the main pool pump to drain and letting it suck air.
- Letting the discharge flow back toward the pool or onto the foundation.
- Leaving the pump unattended and running dry.
- Draining an inground pool without checking groundwater conditions.
- Leaving a vinyl or plaster pool empty for longer than needed.
- Forgetting to turn off the pool’s automatic equipment.
After draining
Once the water is out, clean, inspect and repair what you came to do, then refill as soon as possible. For refilling costs and methods, see whether a hose or a truck is cheaper.