Draining and Refilling

How to Drain a Fiberglass Pool Safely

Fiberglass pools are usually not meant to be fully drained. Learn the risks, safer alternatives such as partial drains, and what to ask before emptying one.

On this page
  1. Short answer
  2. Why fiberglass is different
  3. Common reasons people want to drain, and what to try instead
  4. If a drain is truly needed
  5. Questions to ask before you start
  6. Partial drains for chemistry problems
  7. Is losing an inch a day normal?
  8. Calcium deposits on fiberglass
  9. What happens to a fiberglass pool after 25 years?

Short answer

In most cases, do not drain a fiberglass pool yourself. Manufacturers and installers generally advise against a full drain without their guidance, and some warranties may be affected if you do. Most problems that make owners want to drain, such as algae, cloudy water or high stabilizer, have safer fixes.

If a full drain really is needed, treat it as a job for the manufacturer, the installer or an experienced fiberglass pool technician.

Why fiberglass is different

A fiberglass pool is a one-piece shell set into the ground and surrounded by backfill. The weight of the water inside pushes outward against the walls and downward on the floor, balancing the pressure of the soil and groundwater outside.

Take the water away and that balance changes:

  • Floating: groundwater can push up on a lightweight empty shell, lifting it. The same underground pressure that affects concrete pools is a bigger concern for a shell that weighs much less. See hydrostatic pressure and inground pools for more.
  • Wall bulging or buckling: the backfill can press the walls inward.
  • Floor cracking or splitting: uneven pressure can stress the shell, with knock-on damage to plumbing and decking.
  • Warranty problems: many manufacturers say an unsupervised drain can void coverage. Check your own paperwork.

Common reasons people want to drain, and what to try instead

Problem Try this first
Green or cloudy water, algae Test, balance, shock, brush, vacuum and filter for several days
Storm debris Skim, vacuum and run the filter
High cyanuric acid (stabilizer) A series of partial drains and refills, or a reverse osmosis service
High calcium hardness Partial drains with fresh water, or reverse osmosis
Stains or scale Ask the manufacturer which treatments are safe for your finish

Seeking professional help is a good move if the problem does not respond. You can also read how often a pool actually needs to be drained.

If a drain is truly needed

Occasionally a repair or surface job cannot be done underwater. In that case, professionals commonly follow safeguards like these:

  • Check groundwater first. Some fiberglass pools have a dewatering or sump port so groundwater can be checked and pumped out before and during the drain.
  • Brace the shell. Wood bracing across the pool, wall to wall, can help hold the walls in shape while it is empty.
  • Pick dry weather. Avoid draining during rainy periods or when the ground is saturated.
  • Work fast and refill promptly. Aim to leave the shell empty for as short a time as possible, in many cases the same day.
  • Do not leave it empty overnight unless the manufacturer says it is fine.

Only the manufacturer or installer can say what is right for your specific model, soil and setup, so do not treat this list as a substitute for their instructions.

Questions to ask before you start

  • Does my warranty allow draining, and under what conditions?
  • Does my pool have a dewatering port or other groundwater relief?
  • What is the water table like at my property?
  • Who should do the work?
  • How should the shell be braced, and how fast should it be refilled?

Partial drains for chemistry problems

If the issue is chemical, you may not need to go anywhere near the floor of the pool. Lowering the water by a few inches or to just below the skimmer or returns, then refilling, reduces the concentration of dissolved minerals and stabilizer. Repeat if needed after retesting. Do not drain below the point your manufacturer recommends, and never lower the level far enough to expose the shell’s lower sections without advice. For the general approach see our pool draining and refilling guide.

Is losing an inch a day normal?

Not usually. Evaporation depends on heat, wind and humidity, but an inch a day is more than many pools lose through evaporation alone. A bucket test can help: place a bucket of pool water on a step, match the water level inside to the pool’s, mark both, and compare after a day or two. If the pool falls further than the bucket, suspect a leak and have it checked. Do not drain a fiberglass pool to hunt for the leak.

Calcium deposits on fiberglass

Calcium scale usually builds up at the waterline and on tile when hardness and pH run high. Prevention is easiest: keep the water balanced. For existing scale, ask your manufacturer which cleaners and tools are safe for the gelcoat, because harsh acids and abrasive pads can damage the finish. A gentle, non-abrasive approach at the waterline, plus lowering the hardness through partial drains if it is high, is a common starting point.

What happens to a fiberglass pool after 25 years?

Fiberglass pools can last a long time with good care. With age, owners may see fading, a rougher or chalky surface, staining, small cracks or blisters. Many of these can be repaired or refinished by a specialist, sometimes with the pool kept filled. If a repair does need an empty shell, that is the point to involve a professional who understands your pool’s design.

The complete guide to draining and refilling

How to Drain and Refill a Pool
Read the guide

Keep exploring

Guides from other topics

All topics →