The short version: how water moves through a pool
Most residential pools work as a loop. The pump pulls water out of the pool through the suction side (skimmers and, in many pools, a main drain). The water passes through the pump, then through the filter, then through any heater or sanitizer, and goes back into the pool through the return side (the return jets or inlets).
In order, the path is usually:
- Skimmer and/or main drain
- Suction pipes and valves
- Pump and strainer basket
- Filter
- Heater, chlorinator or other equipment, if installed
- Return pipes and return fittings
Knowing this order makes troubleshooting easier. A clog or an air leak before the pump behaves differently from a leak after it, and the fix depends on which side you are dealing with.
The suction side
Skimmers
A skimmer is the opening in the pool wall near the water surface. Surface water, along with floating leaves, insects and other debris, is drawn in and caught in a removable basket. Inside the opening there is usually a small hinged flap called a weir gate, which helps direct surface water into the skimmer and keeps debris from drifting back out when the pump stops.
The skimmer only works properly when the water level is in the right range. See where the water level should sit on a skimmer for details.
Main drain
Many inground pools also have a main drain, a suction outlet at the lowest point, usually in the deep end. Despite the name, it is not normally used to empty the pool. It adds circulation from the bottom of the water, which can help with even chemical distribution and temperature, and it picks up some fine debris. Not every pool has one, and many newer designs rely on skimmers alone.
Pump and strainer basket
The pump draws water through the suction lines. A second basket, the pump strainer basket, sits in front of the impeller and catches whatever got past the skimmer. A cracked lid, a worn lid o-ring or a loose fitting before the pump can let air in, which shows up as bubbles in the basket or at the return jets. If the pump itself is dripping, see what to check when a pool pump is leaking.
The equipment pad: filter, heater, sanitizer
After the pump, water goes through the filter. The common types are:
- Sand filters, often controlled by a multiport valve with settings such as filter, backwash, rinse, waste, recirculate and closed.
- Cartridge filters, which trap debris in pleated elements that are removed and cleaned.
- DE (diatomaceous earth) filters, which use a powder coating on internal grids.
Depending on the setup, the water may then pass a heater (gas, electric heat pump or solar) and a chlorinator or salt system before it goes back to the pool. Heaters and chlorinators are often installed after the filter so that they only see filtered water.
The return side
Filtered, treated water goes back through underground pipes to return fittings in the pool wall. Return jets are typically angled slightly downward and sideways to promote circulation across the pool. Because the return side is under pressure while the pump runs, a crack or bad joint here pushes water into the ground. Our guide to repairing return line leaks and PVC pipe covers what the repair involves.
Valves that control the flow
Valves let you decide which lines are open. Common ones include:
- Ball or gate valves on the skimmer and main drain lines, so you can favour one or the other
- Diverter valves for features such as a spa, waterfall or solar
- Check valves that stop water from flowing backward
- Unions and isolation valves at the pump and filter so equipment can be serviced
A line that seems clogged is sometimes just a valve that is partly closed, so check valve positions before you start any bigger job.
The pipes themselves
Most residential pool plumbing is PVC. Rigid PVC, usually Schedule 40, is the standard for most installations, while flexible PVC is used in some regions, particularly colder ones. We cover the differences in what type of PVC is used for pool plumbing. Pipe diameters of 1.5 and 2 inches are common for residential lines, although your pool may differ.
Other parts you will hear about
The plumbing sits inside a wider system. Other common terms:
- Shell: the pool structure itself, built of concrete, fibreglass or a vinyl liner on a frame
- Coping: the capping around the top edge of the pool wall
- Deck: the surface surrounding the pool
- Steps, ladders and lights: lights have their own wiring conduit, which is a known place for leaks
Where plumbing problems tend to show up
- Skimmer area: cracks around the skimmer body or faceplate gasket
- Return fittings: loose or cracked fittings, or leaks in the pipe behind them
- Underground pipes: damage from shifting soil, tree roots or freezing
- Equipment pad: pump seals, unions, valves and filter fittings
- Clogs: leaves and debris that get past the baskets and settle in a suction line. See how to unclog a pool line full of leaves
If you are losing water and are not sure where it is going, start with the bucket test and then read our guide to losing water in an inground pool.
Above-ground pools
Above-ground pools use the same loop, but the connections are usually simpler. A skimmer mounts in a rectangular opening in the upper part of the wall, and a return fitting mounts in a round hole in the wall. They are generally connected to the pump and filter with flexible hoses or short runs of pipe rather than long underground lines. Gaskets around these wall fittings are a common place to look for drips.