Pumps and Filters

Diatomaceous Earth (DE) Pool Filter Systems

What a DE pool filter is, how diatomaceous earth traps tiny particles, how to charge and backwash it, and what to know about pool-grade DE and safe disposal.

On this page
  1. What a DE filter is
  2. How a DE filter works
  3. Types of DE filters
  4. Pool-grade vs food-grade DE
  5. How much DE to add
  6. Backwashing and recharging
  7. Handling and disposing of DE
  8. Periodic deep cleaning
  9. Pros and cons

A DE filter uses diatomaceous earth, a fine powder, to coat internal filter surfaces and trap very small particles. It is generally regarded as the finest-filtering of the three common pool filter types, at the cost of more upkeep. This guide explains how it works, how much powder to use, and what to watch out for.

What a DE filter is

Diatomaceous earth (DE) is a powder made from the fossilized remains of microscopic organisms called diatoms. Each particle has a porous, sponge-like structure. In a pool filter, the powder is not a loose bed like sand. Instead, it is deposited in a thin layer on internal grids, fingers or tubes, and it is that coating that does the filtering.

How a DE filter works

  1. The filter has a set of internal elements, often called grids, fingers or flex tubes, covered in fabric.
  2. You add DE powder to the system, normally by pouring a slurry of DE and water into the skimmer. The pump pulls the powder into the filter.
  3. The powder sticks to the fabric and forms a layer, commonly called the filter cake.
  4. Pool water is pushed through the cake and the fabric. The cake traps very small particles, and clean water flows out the other side.

DE filters are usually described as capturing particles in the low single-digit micron range. Figures of about 3 to 5 microns are common, and some sources quote even lower. This is generally finer than a sand filter or a cartridge filter, which is why DE is associated with especially clear water. We compare all three types in our overview of pool pumps and filters.

Types of DE filters

  • Grid filters have flat grids arranged vertically inside the tank.
  • Finger or tube filters use fabric-covered tubes. Some models, often called flex-tube filters, let you refresh the powder with an external bump handle.
  • Regenerative filters are a variation designed to reuse the powder after a “bump” cycle, which can extend the time between full cleanings.

Check which type you have. The cleaning and recharging steps differ in detail, and your manual is the best guide.

Pool-grade vs food-grade DE

Only use DE sold for pool filters. Pool-grade DE has been heat-treated (calcined) to give it the structure that works well for filtration. Food-grade DE is a different product with different properties and is not intended for pool filters. It is sold for uses such as garden pest control and animal feed. Using the wrong one can reduce filtration and may clog the system.

Pool-grade DE contains crystalline silica, which is a respiratory hazard when airborne. When handling the dry powder:

  • Wear a dust mask or respirator designed for fine dust.
  • Pour slowly, away from your face, and avoid doing it on a windy day.
  • Mix into a slurry with water before adding it to the skimmer, if your manual recommends that.
  • Keep it away from children and pets.

How much DE to add

Follow the label for your specific filter. The correct amount depends on the filter’s size, and it is usually shown in a chart in the manual or on the tank. As a rough orientation only, many manufacturers specify something on the order of one pound of DE per ten square feet of filter area, but that is not universal. Too little DE leaves areas of the fabric exposed and lets dirt through. Too much can clog the system and raise pressure.

Some pool professionals suggest adding slightly less than the chart amount after a backwash, because some leftover powder usually remains. If you are unsure, use the manufacturer’s recommendation.

Backwashing and recharging

When the pressure gauge climbs, commonly 8 to 10 psi above its clean level, the filter cake has clogged and needs resetting. The usual sequence is:

  1. Turn the pump off and set the valve to backwash. The exact steps depend on your valve, so follow the general approach described in our guide to backwashing a pool filter.
  2. Run the pump until the water in the sight glass or waste line is clear.
  3. Switch to rinse briefly if your valve has that setting, then return to filter.
  4. Recharge the filter by adding a fresh dose of DE through the skimmer, as described above.

Skipping the recharge is a common mistake. Without the powder coating, the bare fabric filters poorly, and unfiltered particles can get through and even get embedded in the fabric.

Handling and disposing of DE

Backwash water from a DE filter carries used powder. Because DE can clog pipes, some towns and counties restrict where it can go. Many DE systems include a separation tank with a strainer bag so that the powder is caught and can be disposed of with household trash, but rules vary. Check your local requirements before draining DE water to a sewer, storm drain or lawn. If you are not sure, ask your local water authority.

Periodic deep cleaning

Even with proper backwashing, oils and minerals build up in the fabric over time. Many manufacturers recommend taking the filter apart periodically, perhaps once or twice a season depending on use, and hosing the grids or fingers clean. Use a cleaner made for DE filters if recommended, and follow the product’s instructions. If you are using an acid-based product, follow its safety instructions closely and never mix it with chlorine products.

During cleaning, inspect the grids for tears, damaged ribs or crushed fabric. Damaged grids can let DE escape into the pool, where it forms a visible cloud. Our article on how long a pool filter lasts gives typical lifespans for DE grids and tanks.

Pros and cons

Pros

  • Very fine filtration, which can give sparkling water.
  • Can allow better clarity when the pool is heavily used.

Cons

  • More maintenance than sand or cartridge filters.
  • Recharging with powder is an extra step and an ongoing cost.
  • Powder handling and disposal rules need attention.
  • Higher purchase price in many cases.
  • Restricted or discouraged in some areas.

If you value low maintenance more than the finest clarity, a sand filter or cartridge filter may suit you better. If you do choose DE, keep a note of the clean pressure and watch for problems with our pool filter troubleshooting guide.

The complete guide to pumps and filters

Pool Pumps and Filters: How the System Works
Read the guide

Keep exploring

Guides from other topics

All topics →