Hot Tub Care

How to Balance Hot Tub Water

Learn the order to balance hot tub water: test first, then adjust alkalinity, pH, calcium hardness and sanitizer, with typical target ranges for each.

On this page
  1. Quick answer: the order to balance hot tub water
  2. How to check the water in a hot tub
  3. Target ranges at a glance
  4. Step 1: Adjust total alkalinity
  5. Step 2: Adjust pH
  6. Step 3: Adjust calcium hardness
  7. Step 4: Set your sanitizer
  8. Why the order matters
  9. What to do when chlorine is too high
  10. When balancing is not enough

Quick answer: the order to balance hot tub water

Balance a hot tub in this order: test the water, adjust total alkalinity, adjust pH, adjust calcium hardness, then set your sanitizer level. Alkalinity comes first because it acts as a buffer for pH. If alkalinity is off, pH tends to bounce around no matter how much you adjust it.

Make one change at a time, let the jets circulate the water, and retest before adding anything else. The numbers below are typical ranges. Your spa manufacturer or chemical brand may recommend slightly different ones, so check your owner’s manual.

How to check the water in a hot tub

You can test with test strips or a liquid test kit. Strips are quick and fine for routine checks. Liquid kits take a little longer, and many owners find them easier to read precisely.

  • Dip a strip or draw a sample from elbow depth, away from the jets and skimmer.
  • Test before you add chemicals, not right after.
  • Test at least weekly, and again after heavy use, a refill or a rainstorm.
  • Test more often in the first days after a fresh fill, when readings move the most.

Write the results down. A few weeks of readings show you which numbers tend to drift in your tub.

Target ranges at a glance

Reading Typical range
Total alkalinity about 80-120 ppm
pH 7.2-7.8 (many aim for 7.4-7.6)
Calcium hardness about 150-250 ppm
Free chlorine about 1-3 ppm
Bromine about 3-5 ppm

Some sources give a slightly higher alkalinity range, such as 100-150 ppm. If your manual gives a range, use that.

Step 1: Adjust total alkalinity

Total alkalinity measures how well the water resists pH swings.

  • Too low: add an alkalinity increaser. This is usually sodium bicarbonate, the same compound as baking soda. Add it in small doses with the pump running.
  • Too high: add a pH decreaser (usually sodium bisulfate) gradually, following the label. It lowers alkalinity and pH together.

Wait the time the label recommends, then retest. If you know pH is also low, you can aim for the lower end of the alkalinity range, because raising pH often nudges alkalinity up a little.

Step 2: Adjust pH

pH tells you how acidic or basic the water is. Sanitizer works best in the middle of the range, and both extremes cause problems.

  • Low pH can irritate skin and eyes and can be corrosive to equipment.
  • High pH makes sanitizer less effective and can lead to scale and cloudy water.

To raise pH, use a pH increaser (typically sodium carbonate, or soda ash). To lower it, use a pH decreaser (typically sodium bisulfate). Add small amounts, circulate, and retest. Running air blowers or jets aerates the water, and aeration can push pH upward over time. That is one reason pH tends to creep up between tests.

Step 3: Adjust calcium hardness

Calcium hardness matters for protecting the tub and heater.

  • Too low (soft water) can contribute to foaming and can make the water more aggressive toward equipment. A calcium hardness increaser raises it. See soft water and slick or gritty hot tub water for more detail.
  • Too high can lead to scale and cloudiness. No simple additive lowers it. The usual fix is to drain some water and refill with softer water. A scale-control (sequestering) product can help keep minerals in solution.

Step 4: Set your sanitizer

Once alkalinity, pH and hardness are in range, bring your sanitizer to its target level. Chlorine is commonly kept around 1-3 ppm and bromine around 3-5 ppm. If you prefer an alternative, see non-chlorine hot tub sanitizers.

Sanitizer keeps bacteria in check, but it does not remove everything that builds up in the water. Oils, lotions and other organic matter are handled by oxidizing or “shocking” the water. See how to shock a hot tub for the details.

Why the order matters

Each reading affects the others. Alkalinity supports pH, pH controls how well sanitizer works, and hardness affects scale and foam. If you start with sanitizer while pH is far out of range, the sanitizer will not perform as it should and you may end up adding more than you need. Balancing in order avoids a loop of adjusting one number only to knock another out.

What to do when chlorine is too high

If a test shows chlorine well above range, stay out until it comes back down. Take the cover off and let the water circulate. Chlorine falls over time, faster in sunlight and warm water. Diluting with fresh water is another option, though it also changes your other readings. For more detail, see whether you can go in a hot tub if chlorine is too high.

When balancing is not enough

Sometimes the numbers will not hold, or the water stays cloudy or foamy even though readings look right. Common reasons:

If chemistry keeps getting harder to manage, a drain and refill is often the simplest reset. Our guide to how to drain and clean a hot tub walks through it.

Keep exploring

Guides from other topics

All topics →