Hot Tub Care

How to Clean and Replace Hot Tub Filters

How to clean a hot tub filter cartridge with a weekly rinse and monthly deep clean, what to avoid, and when to replace the filter every 12 to 24 months.

On this page
  1. How often should you clean a hot tub filter?
  2. What you need
  3. Step 1: Turn off the power and remove the cartridge
  4. Step 2: Rinse the pleats
  5. Step 3: Deep clean (monthly or when dirty)
  6. Step 4: Rinse thoroughly
  7. Step 5: Dry and reinstall
  8. What to avoid
  9. When to replace the filter
  10. Why clean filters matter

How often should you clean a hot tub filter?

A common routine is:

  • Weekly: rinse the cartridge with a garden hose.
  • Monthly (roughly): deep clean with a filter cleaner, using a spray or a soak.
  • Every 12 to 24 months: replace the cartridge, or sooner if it is damaged or will not come clean.

Heavy use, lots of oils and lotions, or hard water may call for more frequent cleaning. Check your spa manufacturer’s recommendations too.

What you need

  • A garden hose with a spray nozzle.
  • A cleaner made for spa filters.
  • A clean bucket or large container big enough for the cartridge.
  • A spare cartridge, if possible. Rotating two filters lets one dry while the other runs.

Step 1: Turn off the power and remove the cartridge

Switch the spa off at the breaker or control panel, so the pump cannot run while the filter is out. Remove the cover of the filter compartment and any lid or retaining cap, then lift the cartridge straight out. Check your manual if the design is unfamiliar.

Step 2: Rinse the pleats

Spray the cartridge with a garden hose from top to bottom, working the water between each pleat. Angling the nozzle slightly helps push debris out of the folds. Rotate the filter as you go. You are looking to remove hair, bits of debris and loose dirt.

A weekly rinse like this is often enough to keep the filter working between deeper cleans.

Step 3: Deep clean (monthly or when dirty)

For oils and lotion buildup, rinsing is not enough. Choose one method:

  • Spray method. Spray a spa filter cleaner over the pleats, wait the time the label gives (commonly 15 to 20 minutes), then rinse thoroughly.
  • Soak method. Mix a spa filter cleaning solution in a bucket of water as the label directs and submerge the cartridge for the time stated. Many products suggest several hours or overnight.

Some owners also use a separate scale-removing soak when hard water leaves white deposits on the pleats. This usually involves an acid-based product, so follow the manufacturer’s instructions and safety directions closely. Never mix cleaners together, and rinse the cartridge completely afterwards.

Step 4: Rinse thoroughly

Rinse until no suds or cleaner residue remain. Leftover cleaner can cause heavy foaming when you restart the tub. See foamy hot tub water.

Step 5: Dry and reinstall

Let the cartridge dry fully if you can, and then reinstall it. Drying helps prevent mildew and odors. Seat it properly in the housing and secure the cap or lid, then turn the power back on. If you have two cartridges, put the clean dry one in while the other dries, so you do not run the spa without a filter.

What to avoid

  • Household cleaners, dish soap, bleach and laundry detergent. They can damage the filter media and cause heavy foam.
  • Pressure washers. High pressure can tear or flatten the pleats.
  • Running the spa without a filter for any length of time.
  • Skipping the rinse after using cleaner.

When to replace the filter

Replace the cartridge when:

  • It has frayed fabric, cracked end caps or collapsed pleats.
  • It is still discolored or smelly after a deep clean.
  • Water stays cloudy or flow stays weak even though the filter is clean. See how long cloudy hot tub water takes to clear.
  • It is about 12 to 24 months old, or older than your manufacturer suggests.

Buy a cartridge that matches your spa’s model and size, as sizes vary.

Why clean filters matter

A clean filter removes particles that cause cloudy water, helps your sanitizer work more efficiently, and keeps water flowing freely through the pump and heater. A dirty filter can restrict flow, which may trigger errors and strain the equipment. See why your hot tub is not circulating water. Filters can also harbor slime, so replace or clean them when you purge the system. See how to tell if you have biofilm in a hot tub.

It is a good habit to clean the filter whenever you drain the tub. See how to drain and clean a hot tub, and keep your chemistry in line with how to balance hot tub water.

The complete guide to hot tub care

How to Balance Hot Tub Water
Read the guide

Keep exploring

Guides from other topics

All topics →