Cartridge filters are popular because there is no backwashing, but the cartridge itself needs hands-on cleaning. Done well, it extends the cartridge’s life. Done carelessly, with a pressure washer or the wrong chemical, it can ruin the pleats. This guide covers when to clean, how to do it safely, and what to avoid.
When to clean
- By pressure. Note the clean pressure after each cleaning. When the gauge rises roughly 8 to 10 psi above that baseline, it is time to clean.
- By flow and water quality. Weak flow at the returns or water that is losing clarity can mean a loaded cartridge.
- By schedule. Many sources suggest checking every few weeks to months, and cleaning at least a few times a season, especially before closing a pool for winter. Heavily used or leafy pools need more frequent cleaning.
If the pressure rebounds within a day or two of cleaning, the cartridge may be oil-fouled, scaled or worn out. See the last section.
What you’ll need
- Garden hose with a spray nozzle (a dedicated filter-cleaning nozzle is an inexpensive option).
- A clean bucket or tub, tall enough for the cartridge, for soaking.
- A cartridge cleaner or degreaser designed for pool filters, if the cartridge is oily.
- Silicone-based pool lubricant for the tank O-ring.
- Gloves and eye protection, especially if you use any chemical.
Step-by-step: remove and hose off
- Turn the pump off at the timer and breaker.
- Release the pressure by opening the filter’s air relief valve until the gauge reads zero. Stand to the side.
- Drain the tank if it has a drain plug.
- Open the tank. Remove the clamp, locking ring or lid fasteners as your model requires. Take note of how everything fits.
- Lift out the cartridge or cartridges carefully. If there are several, handle each the same way.
- Inspect it before cleaning. Look for cracks in the end caps, frayed or torn pleats, crushed or flattened sections, or loose or missing bands. A damaged cartridge should be replaced rather than cleaned.
- Rinse the pleats. Set the cartridge on a clean, sloped surface where water drains away. Using a nozzle on a steady spray, hold the hose at an angle and work from the top down, pleat by pleat. Rotate the cartridge and repeat. Flip it over and repeat. Several passes are often needed, because water can push dirt from one area to another.
- Rinse until the runoff is clear.
A garden hose is the main tool here. A pressure washer, a very narrow jet held close, or a stiff brush can tear or fray the pleats and shorten the cartridge’s life. Some owners use an air compressor on a low setting to avoid water use, but too much pressure can also damage the media. If you try this, start low and follow the cartridge manufacturer’s advice.
Deep cleaning for oils and scale
If hosing leaves the cartridge looking dull, greasy or stiff, or the pressure comes back quickly, you may need a deeper clean.
For oils, sunscreen and organic buildup:
- Soak the cartridge in a cleaner made for pool cartridges, following the product’s directions for mixing and time. Some commercial cleaners are designed for this.
- Some owners use a household degreaser or dishwasher detergent solution. If you choose to do so, check the cartridge manufacturer’s guidance first, because not every product is approved.
- Rinse thoroughly with clean water afterwards, until no suds or smell of cleaner remain.
For mineral scale (white, crusty deposits):
- Some manufacturers allow a dilute acid soak, and some owners use diluted vinegar as a milder option. If you consider acid, read the product label and your cartridge manufacturer’s guidance first, wear gloves and eye protection, work outdoors, and always add acid to water, never water to acid.
- Degrease first if the cartridge is oily. Applying acid to an oily cartridge can lock oils into the fabric.
- Do not leave the cartridge soaking longer than directed.
Never mix cleaning chemicals. Combining chlorine bleach with acid or with some other cleaners can release toxic gas. Rinse out buckets between products, and do not store chemicals together.
Reassembly and restart
- Rinse the tank interior and remove debris from the bottom.
- Check the O-ring on the tank lid or clamp. It should be clean, flexible and uncracked. Lubricate it lightly with a silicone-based pool lubricant, and replace it if dry or damaged. A poor seal lets air in.
- Let the cartridge drain. Some owners let it dry fully before reinstalling, and it is a good idea to keep a spare set so one can rest while the other works.
- Reinstall the cartridge in the same orientation, seated on its base, and refit the top manifold if your filter has one.
- Close the tank and secure the clamp or ring fully. Replace the drain plug.
- Open the air relief valve, start the pump, and let air escape until a steady stream of water comes out. Close the valve.
- Note the new clean pressure on the gauge. That is your baseline for next time.
- Check for leaks at the lid and fittings.
Mistakes that ruin cartridges
- Using a pressure washer or a sharp jet at close range.
- Scrubbing hard with a wire or stiff brush.
- Skipping the degrease on oily cartridges and going straight to acid.
- Mixing chemicals such as bleach and acid.
- Soaking for too long or in too strong a solution.
- Reinstalling a damaged cartridge with torn pleats or loose bands.
- Forgetting the O-ring, which can lead to leaks or air in the system. See pool filter troubleshooting.
- Running the pump with the filter lid loose or the air relief valve forgotten.
When cleaning isn’t enough
Cartridges wear out. Many last somewhere around 1 to 3 years, depending on use. Consider replacing if:
- Pleats are frayed, torn, crushed or collapsed.
- End caps are cracked, or bands are loose or missing.
- Pressure rises again shortly after each cleaning.
- Water stays cloudy even though the chemistry is balanced and the cartridge has been cleaned.
- Cleaning needs to happen far more often than it used to.
Our guide on how long a pool filter lasts lists typical lifespans for all filter types, and the overview of pool pumps and filters compares cartridge filters with sand and DE systems.