Pumps and Filters

How a Sand Pool Filter Works

See how a sand pool filter cleans water, what the tank, laterals and multiport valve do, which sand to use, and when the sand needs to be replaced.

On this page
  1. The short version
  2. What’s inside a sand filter
  3. How water moves through it
  4. What the valve positions do
  5. What a sand filter catches and misses
  6. Filter sand: what to buy and what not to
  7. How often to replace the sand
  8. Common sand filter problems
  9. Pros and cons

A sand filter cleans pool water by pushing it through a deep bed of specially graded sand. Dirt and debris get trapped between the grains, and the cleaned water flows back to the pool. It is one of the simplest and most common home pool filters, and it is popular because it is durable and needs little regular attention beyond backwashing.

The short version

  1. The pump pushes water into the top of the filter tank.
  2. The water spreads out over the sand and flows down through it.
  3. Particles are caught in the sand.
  4. Slotted pipes at the bottom, called laterals, collect the filtered water.
  5. The water rises up a central standpipe, passes through the valve and returns to the pool.

When the sand gets loaded with dirt, water has a harder time getting through, and the pressure gauge rises. Reversing the flow, called backwashing, flushes the trapped dirt out to waste.

What’s inside a sand filter

  • Tank. A sturdy shell, usually plastic or fiberglass, that holds the sand and withstands system pressure.
  • Sand bed. The filter medium. Water has to find its way between the grains, so particles are caught along the way.
  • Laterals. A cluster of slotted pipes at the bottom of the tank. The slots are narrow enough to keep sand in and let water out.
  • Standpipe. A central pipe that carries the filtered water up to the valve.
  • Multiport or push-pull valve. The control for the filter’s different modes.
  • Pressure gauge. Shows how hard the pump is working to push water through the sand.
  • Sight glass (on many models). A small clear section on the waste line that lets you see when backwash water runs clear.
  • Air relief valve and drain plug. For releasing pressure and draining the tank.

How water moves through it

In normal filter mode, water flows downward. Gravity and pump pressure both help. Larger particles are caught near the top of the bed and smaller ones deeper down. As the bed collects dirt, it can actually catch a little finer material than it did when clean, which is why a slightly dirty sand filter is not a problem. It is also why pressure, not appearance, should tell you when to clean.

What the valve positions do

Check your own valve’s labels, since they vary by brand. The common positions are:

  • Filter. Normal operation.
  • Backwash. Reverses the flow to flush trapped dirt out of the bed.
  • Rinse. Runs water down through the bed briefly after backwashing to resettle the sand and flush loose dirt out.
  • Waste. Sends water straight to the waste line, bypassing the sand. It is useful for lowering the water level or vacuuming heavy debris to waste.
  • Recirculate. Sends water from the pump straight back to the pool without filtering. Handy if the sand needs to be bypassed temporarily.
  • Closed. Blocks flow. Only use it with the pump off.
  • Winterize. Present on some valves; leaves the valve slightly open for off-season storage.

Always turn the pump off before moving a multiport valve handle. Turning it while the pump runs can damage the internal gasket.

What a sand filter catches and misses

Sand filters are good at removing visible debris and many fine particles, and are commonly rated to catch particles down to roughly 20 to 40 microns. Cartridge filters are often quoted as filtering to somewhat finer sizes, and DE filters finer still, as described in our overview of pool pumps and filters and in the DE filter guide. A sand filter does not remove bacteria or dissolved material, so sanitizer and balanced water are still essential.

Filter sand: what to buy and what not to

Use sand sold specifically for pool filters. It is usually a graded silica sand, commonly sold as #20 silica sand, with a grain size around half a millimeter. The grain size and shape matter because they control how water passes through and what gets trapped.

Ordinary sand is not a substitute. Play sand, beach sand and construction sand have the wrong grain size and often contain dust or other material that can clog the bed or slip through the laterals. Some owners choose alternative media such as crushed glass or zeolite-based products, which manufacturers claim filter finer and last longer. Check that your filter’s manufacturer approves any alternative before using it.

How much sand? The amount depends on the tank. Look for the filter’s label or manual, which lists the required sand weight, and measure out that amount. Using too little or too much can hurt filtration and cause sand to wash into the pool.

How often to replace the sand

Many sources suggest replacing sand every 3 to 5 years, with some saying it can last up to about 7. The sand grains wear and lose their sharp edges, and oils and minerals can bind the bed. Your pool use, water chemistry and filter care all affect the number. Signs the sand may be worn include:

  • Water stays cloudy even when chemistry is balanced.
  • You need to backwash far more often than before.
  • Pressure rises quickly after a backwash.
  • Sand has hardened into clumps or the bed has channeled (below).

Replacing the sand is a manageable DIY job for many people, but it involves removing the valve, scooping out old sand, inspecting the laterals and refilling carefully. Costs vary by the amount of sand and whether you hire help. Our article on how long a pool filter lasts lists typical lifespans for the other filter types too.

Common sand filter problems

  • Channeling. Water carves paths through the sand instead of spreading evenly, which reduces filtering. Hardened or worn sand is a common cause.
  • Sand in the pool. A small amount of sand after fresh sand is installed can happen. Ongoing sand in the pool, especially coming out of the return jets, often points to a cracked lateral or a damaged standpipe.
  • Pressure that never drops after backwash. This can mean fouled or hardened sand, a clogged line or a bad gauge. See pool filter troubleshooting.
  • Water leaking from the valve. Often a worn gasket or O-ring.

Pros and cons

Pros

  • Simple design, long-lived tank.
  • Low ongoing cost, with no cartridges to buy.
  • Backwashing is quick.

Cons

  • Backwashing uses water, and in some areas the discharge is regulated.
  • Less fine filtration than cartridge or DE filters.
  • Sand eventually needs replacing, and the job is heavy and messy.

If you choose a sand filter, learn to backwash it properly and keep a note of its clean pressure so you can tell when it is due.

The complete guide to pumps and filters

Pool Pumps and Filters: How the System Works
Read the guide

Keep exploring

Guides from other topics

All topics →