Draining and Refilling

How to Drain and Refill a Pool

Learn when draining a pool is worth it, how to remove the water safely by pump, siphon or drain, and how to refill, rebalance and estimate the cost.

On this page
  1. Should you drain at all?
  2. Know your pool type first
  3. What you need
  4. Where the water can go
  5. Ways to remove the water
  6. Draining an above-ground pool
  7. Draining an inground pool
  8. Cleaning and inspecting while empty
  9. Refilling and rebalancing
  10. What it costs
  11. How much water should a pool lose?
  12. Quick answers

Should you drain at all?

Many pool problems that feel like they need a fresh start do not. Cloudy water, algae and a bad smell can usually be handled with testing, shocking, brushing, vacuuming and a few days of filtration. Draining is more often justified by:

  • a repair or resurfacing job that cannot be done underwater, such as replacing a vinyl liner or re-plastering;
  • very high dissolved solids or stabilizer (cyanuric acid) that dilution cannot fix;
  • hard-water scale or staining that other treatments have not cleared.

Even then, a partial drain and refill is often enough, since it dilutes the problem without leaving the pool empty. If you are weighing it up, see how often a pool really needs to be drained.

Know your pool type first

How you drain depends on what the pool is made of.

  • Above-ground pools with vinyl liners: the walls rely on the water for support, and a liner left dry in the sun can shrink and pull out of position.
  • Inground vinyl, concrete and plaster pools: these can be damaged by groundwater pressure when empty. Read how hydrostatic pressure affects inground pools before you start.
  • Fiberglass pools: manufacturers commonly advise against draining without their involvement. See draining a fiberglass pool safely.

If you are unsure, check your pool’s documentation or ask the installer or manufacturer first.

What you need

  • A submersible utility pump with a float switch if possible, or a way to use your filter’s waste setting.
  • Enough hose to reach your discharge point, plus clamps or adapters.
  • A GFCI-protected outlet and a suitable outdoor extension cord if the pump is far from power.
  • A wet/dry vacuum or sponges for the last bit of water.
  • Soft brushes and a non-metal scoop if you are cleaning the floor.
  • Test strips or a test kit, for both the draining and the refill stage.

Where the water can go

Pool water needs somewhere to go, and rules differ by location. Some municipalities ask you to discharge to a sanitary sewer cleanout, others permit the street or storm drain only after the water has been dechlorinated, and some restrict discharge altogether. Check with your local water or stormwater authority before you pump.

Practical points that apply almost everywhere:

  • Let chlorine drop first. Stop adding chlorine in the days before draining, and test to confirm the level is low. Sunlight helps break chlorine down, particularly if the pool is not stabilized. A neutralizer is an option if you are short of time.
  • Do not point the hose at your foundation, a neighbor’s property or a septic system’s drain field.
  • If you discharge onto the lawn, spread the water out and avoid one concentrated spot. See whether pool water will kill your grass.
  • For inground pools, discharge well away from the shell and downhill, so the water does not seep back under the pool.

Ways to remove the water

Submersible pump

The most common method. Lower the pump into the deepest part of the pool, connect the hose, and plug into a GFCI outlet. Our guide to draining a pool with a submersible pump covers setup and safety in detail.

Filter waste or backwash setting

If your filter has a multiport valve with a waste setting, the pool’s own pump can send water out through the waste line. This is convenient for lowering the level, but do not let the pump run dry, because it can damage it.

Garden hose siphon

Fill a hose with water, keep one end submerged, and lay the other end on lower ground than the pool floor. Gravity does the rest. It is slow, but it needs no electricity and works for smaller pools.

Built-in drain plug

Many inflatable and frame pools have a drain fitting near the bottom that accepts a garden hose adapter. Check the manual for the exact fitting and make sure the hose runs downhill and away from the pool.

Draining an above-ground pool

  • Choose a mild, overcast day if you can. Vinyl liners can shrink and stiffen in the heat once exposed.
  • Drain with a pump or the built-in drain. Never cut the liner to let the water out.
  • If you are cleaning rather than replacing the liner, consider leaving a shallow layer of water in place and working in sections, or work fast and refill promptly.
  • Scoop out debris with a plastic shovel, scrub gently with a soft brush and a pool-safe cleaner, then rinse and vacuum up the dirty water with a wet/dry vac.
  • Check the liner and seams for damage, then start refilling right away.

Do not leave an above-ground pool empty for longer than necessary, and watch the walls as the water level falls.

Draining an inground pool

The main risk is groundwater pushing up on an empty shell. In The Swim describes a “popped” concrete pool as an extremely rare event, mostly tied to major flooding, but it is expensive when it happens, so take precautions:

  • Avoid draining during or right after prolonged heavy rain.
  • Pump the water far from the pool and downhill.
  • If your pool has hydrostatic relief plugs or a relief valve, a professional can open them once the pool is mostly empty.
  • Do not leave the pool empty for long. Plaster and liners dislike sun and dry air.

If you have any doubts about the water table where you live, have a pool professional do the job. The full explanation is in our hydrostatic pressure guide.

Cleaning and inspecting while empty

An empty pool is the best chance you will have to look at the surfaces and fittings. Check for:

  • liner tears, wrinkles and seam problems (vinyl);
  • cracks, hollow spots, rough or flaking plaster (concrete);
  • loose tiles and worn gaskets;
  • debris in the main drain and around returns and skimmers.

Make repairs before you refill, and have materials on hand so the pool is empty for as short a time as possible.

Refilling and rebalancing

  • Fill from a garden hose, or arrange a delivery. See whether a hose or a truck is cheaper.
  • Do not leave a hose running unattended for hours. Set a timer.
  • Keep an eye on the walls and liner for wrinkles while the water rises.
  • Reattach and prime the pump and filter once the water covers the skimmer opening, and check for leaks.
  • Test the new water. Fresh fill water often needs adjustments to pH, alkalinity and calcium hardness, and a stabilizer level if you use one.
  • Add sanitizer and get the chlorine into range before anyone swims.

If you are using new water with mineral content, test before you add chemicals so you correct what is actually needed.

What it costs

The cost has two parts: getting rid of the old water and buying the new water.

  • Doing it yourself costs pump rental or purchase, electricity and the replacement water.
  • Hiring a service adds labor, and prices vary widely by region and pool size. Get quotes rather than relying on averages.
  • The new water is volume times your local rate. To estimate volume, multiply for a rectangle: length x width x average depth x 7.5 gallons per cubic foot. For a round pool: diameter x diameter x average depth x 5.9. Then multiply thousands of gallons by your utility’s rate, and ask whether a sewer charge also applies to the fill. Some utilities waive or credit it for pool fills; others do not.

Delivery is covered in hose versus truck costs.

How much water should a pool lose?

Some loss is normal, mostly from evaporation, and it rises with heat, wind and dry air. A pool that drops by a small amount over a week is usually evaporating. A pool losing an inch or more a day deserves attention, since that is more than ordinary evaporation typically explains. A bucket test helps tell the two apart: set a bucket of pool water on a step with its water level matching the pool’s, mark both, and compare after a day or two. If the pool drops further than the bucket, suspect a leak. Common trouble spots include skimmers, return fittings, light niches, plumbing and the liner or shell itself.

Quick answers

What is a hydrostatic valve? It is a relief fitting in the floor or main drain of some inground pools that lets groundwater enter the shell, equalizing pressure when the pool is empty.

How can I pump the water out of my pool? A submersible utility pump is the usual choice, and the filter’s waste setting or a siphon can work too.

How do I empty an Intex pool? Most have a drain plug on the wall that accepts a garden hose adapter. Check your model’s manual.

Keep exploring

Guides from other topics

All topics →