Draining and Refilling

Hydrostatic Pressure: Can You Safely Drain an Inground Pool?

An empty inground pool can be pushed up by groundwater, though it is rare. Learn how hydrostatic pressure works and how to reduce the risk when draining.

On this page
  1. Short answer
  2. What hydrostatic pressure is
  3. How big is the risk?
  4. How to reduce the risk
  5. Hydrostatic relief plugs and valves
  6. Pool type differences
  7. Warning signs
  8. When to call a professional

Short answer

Yes, many inground pools are drained safely, but the risk of groundwater lifting an empty pool is real enough to plan for. In The Swim, a pool supply retailer, describes a concrete pool that “floats” or pops out of the ground as an extremely rare event, mostly associated with major flooding or hurricanes. Rare is not never, and the repair can be very costly, so take precautions or hire someone who does this regularly.

What hydrostatic pressure is

Hydrostatic pressure is the pressure exerted by water in the ground. Soil around and under your pool holds water, and when the water table rises, that water pushes up against the pool shell, the same way water pushes up on a boat.

With a full pool, the weight of the water inside, roughly 8 pounds per gallon, helps hold the pool down and resist that pressure. In The Swim notes that water makes up most of an average inground pool’s weight when full. Drain the pool and that counterweight disappears. If the groundwater pressure is higher than the empty shell’s weight and anchoring, the floor can crack or the pool can lift.

How big is the risk?

It depends on your site. The risk is higher when:

  • the water table is high, for example near a river, lake, coast or in low-lying land;
  • the soil is clay or drains poorly, so water collects around the shell;
  • there has been heavy or prolonged rain, or flooding, recently;
  • the ground slopes toward the pool, so runoff collects around it;
  • the pool is lightweight, as with fiberglass shells;
  • you pump the discharge water near the pool, where it soaks back into the ground around the shell.

If your area is dry, the soil drains well, and the weather has been settled, the risk is lower. Local pool builders usually know what the water table looks like in your area.

How to reduce the risk

These tips follow guidance commonly given by pool professionals:

  1. Do not drain during or after extended heavy rain. A few hours of heavy rain can send water toward the pool, so choose a dry stretch.
  2. Discharge far away from the pool. Water that you pump out can seep back under the shell if the hose ends too close. Using a storm drain, where allowed, or a distant point on the property helps.
  3. Pump downhill. Look at the slope of the land and pick a spot where water runs away from the pool. If there is no downhill, use more hose and move the end regularly to avoid saturating one area.
  4. Open the hydrostatic relief plugs or valve. Many concrete and plaster pools have these in the floor. See below.
  5. Work quickly. Do not leave an inground pool empty for long. Plaster and liners dislike sun and dry air, and a longer empty time gives groundwater more chance to rise. Have supplies and helpers ready before you start, and aim to refill within about a week at most for repair work, and sooner if you can.

For the mechanics of the draining itself, see how to drain a pool with a submersible pump.

Hydrostatic relief plugs and valves

Many inground concrete or plaster pools have one or more plugs set in the floor, and sometimes a plug in the bottom of the main drain pot. They are meant to let groundwater into the pool, instead of pushing the shell up, when the pool is empty.

In The Swim describes the usual process this way: once the pool is mostly drained, the plaster over a plug is broken out and the threaded plug is removed, and some pools may call for more than one to be opened. This is not a task to improvise. Plugs can be glued, hidden under plaster, or in unexpected places, and opening one turns the pool floor into a place where groundwater will enter. After the work you will need to know how to reseal or reinstall them correctly. A pool professional can handle that, and they will know what is typical for your pool’s design.

Not every pool has relief fittings, so check your pool’s plans, ask the original builder, or have a professional look.

Pool type differences

  • Concrete and plaster pools: heavy, but the floor can still crack or lift. Relief plugs are common.
  • Vinyl-liner pools: groundwater can lift the liner, causing large bubbles or “floating” of the liner, and in extreme cases lift the pool structure. Keep empty time short and follow the installer’s advice.
  • Fiberglass pools: a lightweight shell means more risk. Many manufacturers say not to drain without their guidance. Read how to drain a fiberglass pool safely.

Warning signs

Stop pumping and get advice if you see:

  • water bubbling up from the floor, cracks or relief fittings;
  • a floor that appears to bulge or move;
  • liner bubbles forming, or the liner lifting from the walls;
  • cracks opening up in the shell or deck;
  • standing water or saturated ground close to the pool.

Refilling can sometimes relieve the problem, but ask a professional first.

When to call a professional

Consider hiring someone if:

  • you know or suspect a high water table;
  • the area has flooded before or has had a lot of rain;
  • the pool is fiberglass or has no known relief fittings;
  • you need a full drain for repairs;
  • you are unsure about the plugs, valves or discharge location.

You may also be able to avoid a full drain entirely. For chemistry problems, a partial drain is often enough, and how often a pool needs to be drained explains when a full one makes sense. For a general walkthrough, see our guide to draining and refilling a pool.

The complete guide to draining and refilling

How to Drain and Refill a Pool
Read the guide

Keep exploring

Guides from other topics

All topics →