Divots, bubbles and wrinkles: what is the difference?
All three show up as irregularities in a vinyl liner, but they point to different causes:
- Divots (dents or depressions) are low spots in the floor, often where the base underneath has shifted, washed out or been compressed.
- Bubbles (bulges or air or water pockets) are raised areas where air or water has gotten behind the liner.
- Wrinkles are folds or creases, often from a liner that is slightly oversized, installed in cold conditions or has shifted.
Identifying which you have is the first step, because the fixes are different.
What causes divots
Divots usually trace back to what is under the liner rather than the liner itself.
- Base erosion or washout. Sand or other base material can wash away if water gets behind the liner, leaving a hollow.
- Footprints and compaction. If the base was not smooth and firm when the liner was installed, the weight of the water can press a footprint or tool mark into it.
- Settling. Soil under the base may settle unevenly, especially after new construction or heavy rain.
- Objects under the liner. A stone, root or debris can leave a visible bump, while the area around it can sink.
- Sand migration. On some pools, sand moves towards the deep end or toward walls, leaving thin spots elsewhere.
Dealing with divots
Small, shallow divots are often cosmetic. The liner is still supported by water pressure, and many pool owners choose to monitor them rather than repair them. Things to check:
- Is the pool losing water? A depression combined with unexplained water loss can mean water is escaping and washing the base away. See the section below on water loss.
- Is the divot growing? A divot that deepens or spreads suggests ongoing erosion.
- Is there a sharp object underneath? If you can feel a hard point through the liner, it is worth addressing before it punctures it.
Fixing a divot properly usually means lowering the water, lifting the liner and rebuilding the base underneath with appropriate material, then reinstalling the liner. This is a job that carries a risk of damaging the liner or the walls, especially in above ground pools where draining can stress the structure, so check the manufacturer’s guidance or hire an experienced installer. If a pool is due for a new liner anyway, it is also a good time to fix the base. For ideas on materials, see what to put underneath an above ground pool.
What causes bubbles
Bubbles under a vinyl liner generally come from one of these:
- Groundwater and hydrostatic pressure. In inground pools, heavy rain, snowmelt or a high water table can push water in around the pool, lifting the liner. If the water level inside the pool is low, there is less weight holding the liner down.
- Water or air leaking behind the liner. A leak in the liner, return line or fitting can send water behind the vinyl.
- Trapped air from installation. Air that was not fully removed with the vacuum during installation can create small pockets.
- Gas or temperature effects. Warm or cold conditions can affect how the liner sits against the wall or floor.
Fixing bubbles
- Keep the pool at its normal operating level. Water pressure helps hold the liner against the floor and walls. Do not drain an inground vinyl pool in response to a bubble without professional advice. A drained pool in saturated ground can have its liner or even the pool structure damaged by groundwater pressure.
- Look for the cause. After heavy rain, bubbles can appear and often settle as the ground dries out. If they persist or appear without rain, suspect a leak.
- Remove trapped water or air. Some owners use a wet and dry vacuum with a small hose slid under the liner edge to draw out trapped fluid. Be careful not to puncture the liner and consider asking a professional if the bubble is large or in a tricky spot.
- Improve drainage around the pool. Direct runoff and downspouts away from the pool and deck.
- Leave fixes involving hydrostatic relief to professionals. Inground pools can need drainage or relief systems that are not do-it-yourself work.
Is the pool losing water?
Water loss is a clue to which problem you have. A common first check is the bucket test: set a bucket partly filled with pool water on a step so the water levels inside and out match, mark both, and compare after a day or so. If the pool drops more than the bucket, there may be a leak beyond normal evaporation. Evaporation, splashing and backwashing also lower the level, so rule those out first. If you suspect a leak, find it before it undermines the base. How to tell if a pool liner is bad covers other signs of failure.
Preventing liner problems
- Prepare the base carefully and smoothly before installing the liner or setting up the pool.
- Keep water levels and chemistry in the recommended range, as outlined in our pool maintenance basics.
- Fix leaks promptly.
- Manage drainage around the pool.
- Avoid dragging sharp objects across the liner and use a soft brush.
When to call a professional
If bubbles keep returning, if the divots are large or the pool is losing water, or if you are unsure about draining, ask a local installer. If the liner is old and brittle, replacement may be a better investment than patching; see what it costs to replace an above ground pool liner and how long above ground pools last.