Routine Maintenance

How to Set Up an Intex Above Ground Pool

A step-by-step overview of setting up an Intex above ground pool: choosing a site, preparing the ground, laying out the pool, filling it and connecting the pump.

On this page
  1. Before you start: pick the site
  2. Prepare the ground
  3. Lay out the pool
  4. Filling and adjusting
  5. Connecting the pump
  6. First water chemistry
  7. Common setup mistakes
  8. How long will it last?

Before you start: pick the site

Most of what goes wrong with a new Intex pool traces back to the spot it was set up on. Take time over this step.

  • Flat and firm. The ground should be level across the full footprint of the pool. A pool set on a slope will fill unevenly, and the walls or frame can be stressed.
  • Clear of overhead hazards. Keep it away from overhanging branches and power lines.
  • Away from buried utilities. Before digging or leveling, check for buried lines. In many places you can request a free utility locate before any excavation.
  • Reasonable access to power. Pool pumps need a properly protected outlet, normally a GFCI-protected circuit, and the cord should not be stretched or run through water. Follow the manual and local code, and ask an electrician if you are unsure.
  • Out of heavy drainage paths. Avoid low spots where rainwater collects.

Check your local rules too. Some areas require permits or fencing even for temporary pools.

Prepare the ground

  1. Clear the area. Remove grass, rocks, roots, sticks and anything sharp. Soft liners can be punctured by small stones.
  2. Level it. Level by removing high spots rather than building up low ones with loose soil, which can settle unevenly under the weight of the water. If the site is far from level, move the pool or get help; see how to level an above ground pool for what leveling involves.
  3. Add protection. Intex usually supplies a ground cloth with its pools. Many owners also add foam tiles or a pool pad. For options and trade-offs, see what to put underneath an above ground pool.
  4. Support the legs on frame pools. If you have a metal frame model, the legs concentrate weight on small areas. Flat pavers or leg pads under each leg are commonly used to stop them sinking.

Lay out the pool

Models differ, so use the manual that came with yours. In general:

  • Easy Set style pools have an inflatable top ring and a soft wall. Spread the pool flat on the ground cloth with the drain valve closed and the inlet and outlet fittings oriented where you want the pump, then partially inflate the ring.
  • Metal frame style pools are assembled from poles and connectors and then have the liner hung from the frame. Assemble on the ground cloth, make sure every connector is fully seated, and keep the frame square.

Smooth out large wrinkles in the liner by hand before adding water. A few small wrinkles on the floor are normal; they tend to settle as the pool fills.

Filling and adjusting

Begin filling slowly and watch the shape. For many models you add a few inches, then walk around the pool smoothing the floor, checking that walls are straight and that the pool is sitting level. If one side is rising faster, stop and sort out the problem before it gets deeper.

Follow the manufacturer’s fill line. Overfilling can stress the walls, and filling much below the recommended level can leave the pump fittings sucking air. Keep an eye out for anything leaking at the fittings during the first hours.

Connecting the pump

Intex pools usually have two fittings, an inlet and an outlet. The filter pump connects with hoses. The general approach:

  1. Fill the pool above the fittings first.
  2. Attach the hoses, using the clamps or fittings supplied.
  3. Open the strainer valves or plunger valves if the pool has them, then make sure the pump housing is full of water and the air has been released.
  4. Plug the pump into a GFCI-protected outlet and switch on.

If water does not flow, see why an Intex pool pump may not be pumping. Most problems come from trapped air, closed valves or a blocked cartridge.

First water chemistry

Once the water circulates, test it and adjust sanitizer and pH based on the product instructions. Ranges and a weekly routine are covered in our pool maintenance basics guide. A pool that sits untreated for even a few days in hot weather can turn green.

Common setup mistakes

  • Setting up on a slope or soft spot.
  • Skipping the ground cloth, or leaving small stones under it.
  • Filling too quickly without checking level.
  • Overfilling past the recommended line.
  • Pump running dry or with air in the system.
  • Stretching extension cords or using non-protected outlets.

How long will it last?

Soft-sided pools are made for seasonal use, and how long they last depends on UV exposure, storage, care and how well the ground was prepared. See how long above ground pools last for what influences their lifespan.

The complete guide to routine maintenance

Pool Maintenance Basics: A Weekly Routine
Read the guide

Keep exploring

Guides from other topics

All topics →