Routine Maintenance

Why is my Intex pool pump not pumping?

Troubleshoot an Intex pool pump that runs but does not move water: air in the system, closed valves, low water, clogged cartridge, hose leaks and power problems.

On this page
  1. Short answer
  2. Safety first
  3. 1. Start with the basics
  4. 2. Check valves and hoses
  5. 3. Release air
  6. 4. Clean the filter and strainer
  7. 5. Check seals and connections
  8. 6. Sand filter pump specifics
  9. 7. If the motor hums or will not run
  10. 8. Is the pump the right size?
  11. When to replace the pump or contact support

Short answer

When an Intex pool pump runs but does not move water, the cause is usually something simple: air trapped in the pump, closed valves or a pinched hose, water level below the fittings, or a clogged cartridge or strainer. Less often it is a power issue, a hose leak that lets air in, or a worn pump. Work through the checks below in order, and check your model’s manual, since parts and procedures differ between models.

Safety first

Switch off and unplug the pump before touching hoses, fittings, the filter or the pump housing. Pool pumps use electricity near water, so use a properly protected outlet (a GFCI circuit) and keep the plug and connections dry. If you see damaged cords, signs of water in electrical parts, or the GFCI keeps tripping, stop and have a qualified electrician look at it.

1. Start with the basics

  • Is it getting power? Check the plug, the outlet and whether the GFCI has tripped. Try the outlet with another device.
  • Is the pump actually running? If you hear nothing, see the section on a pump that does not run, below.
  • Is the water level high enough? The water should be well above the inlet and outlet fittings. If the level has dropped, the pump can suck air. Refill to the recommended level.

2. Check valves and hoses

Many Intex pools have strainer or plunger valves where the hoses connect to the pool wall. These valves close when the hoses are removed, and are meant to open when the hoses are connected. If one is stuck closed, water cannot reach the pump.

  • Make sure the hoses are firmly connected at both ends.
  • Look for kinks or crushed sections, and straighten them out.
  • Check that any valves on the lines are open.
  • If the pool has a strainer grid or a mesh in front of the fitting, make sure leaves or debris are not blocking it.

3. Release air

An air lock is among the most common causes of a pump that will not move water. Intex pumps generally have an air release valve on the filter housing. A typical process, which you should confirm in your manual:

  1. Switch the pump off.
  2. Open the air release valve, usually a small knob or screw on top of the filter, so air can escape.
  3. Let water flow into the housing until water, not air, comes out of the valve.
  4. Close the valve and turn on the pump.

If the pump is above the water level, or the hoses are higher than the water, it can be harder to prime. Make sure both hoses are full of water when you connect them, and consider lowering the pump if the instructions allow.

4. Clean the filter and strainer

A clogged cartridge restricts flow, sometimes until almost nothing comes out.

  • Turn off and unplug the pump, and close the valves if the model has them.
  • Remove the cartridge and rinse it with a garden hose, working between the pleats. A very dirty or aged cartridge may need replacing.
  • Check the strainer basket or grid for leaves.

Keeping debris out of the water helps too. See how to keep leaves out of your pool and our weekly maintenance routine for how often to clean cartridges.

5. Check seals and connections

Air can sneak in through loose or damaged hose connections, worn O-rings, cracked gaskets or poorly seated clamps. Signs include bubbles coming out of the return fitting, or water dripping from connection points. Replace worn seals with parts that match your model, and make sure threaded connections are snug but not overtightened.

6. Sand filter pump specifics

If your pump is a sand filter model, the multiport valve position matters. Make sure it is on the Filter setting for normal operation and has not been left on Closed, Waste or another position. Check the sand level and whether the sand is clumped or clogged, and refer to the manual about backwashing.

7. If the motor hums or will not run

A humming motor that does not turn can mean a jammed impeller or a failing motor. A pump that does not run at all, with power confirmed, may have a failed motor or internal fault. With the pump unplugged, check the impeller area for debris if the manual shows how to access it. Beyond that, motor and electrical repair is usually a job for replacement or the manufacturer’s service rather than home repair.

8. Is the pump the right size?

Pumps are sized for a certain volume of water. If your pool is larger than the pump’s rating, flow may seem weak even when everything works. Compare the pump’s rating to your pool volume in the manual, and see how to set up an Intex above ground pool for connection basics.

When to replace the pump or contact support

If you have checked power, water level, valves, hoses, air, cartridge and seals and flow is still poor, the pump may be worn or damaged. Intex has customer support and replacement parts for many models, and the warranty may apply, so have your model number and purchase information ready. Replacing a pump or filter set is often more practical than repairing it. Keep in mind that equipment wear is part of the cost of ownership; see how long above ground pools last for what to expect.

The complete guide to routine maintenance

Pool Maintenance Basics: A Weekly Routine
Read the guide

Keep exploring

Guides from other topics

All topics →