Backwashing cleans a sand or DE pool filter by running water through it in reverse, flushing trapped dirt out to a waste line. Done at the right time and in the right order, it takes only a few minutes. Cartridge filters do not backwash. They are removed and cleaned, as described in our guide to cleaning a cartridge pool filter.
When to backwash
Go by pressure, not just the calendar.
- After a backwash or a fresh sand change, note the clean pressure on the gauge with the pump running at its normal speed. Write it down or mark the gauge.
- As the filter loads with dirt, pressure creeps up.
- When it is about 8 to 10 psi above your clean baseline, it is time to backwash.
Other triggers include reduced flow at the returns, a noticeable drop in water clarity, or a heavy debris event such as a storm or a big pool party. Some sources suggest backwashing every week or two for typical residential pools, but heavily used or leafy pools may need it more often, and lightly used pools less often. Your gauge is a better guide than a fixed schedule.
If you run a variable-speed pump, compare pressures at the same speed. See variable speed pump settings for more on that.
Before you start
- Know your valve. Multiport valves (a handle with labeled positions) and push-pull valves work differently, so check your manual.
- Check the waste line. Make sure the backwash hose or pipe is connected, unobstructed and discharges somewhere allowed. Many areas restrict where backwash water can go, and some regulate chemical content or DE, so check local rules.
- Plan for water loss. Backwashing sends hundreds of gallons out of the pool, in some cases. Be ready to top up afterward.
- Empty the skimmer and pump baskets. This stops debris from being pushed into the filter.
Step-by-step backwash
- Turn the pump off. Never turn a multiport valve while the pump is running. Doing so can damage the internal seal.
- Set the valve to Backwash. On a push-pull valve, follow the manual for the backwash position.
- Turn the pump on. Water now flows backward through the filter and out the waste line.
- Watch the sight glass (if there is one) or the waste water. Run until the water looks clear. This commonly takes about 2 to 3 minutes. Cloudy water going out is good, since it is carrying away dirt.
- Turn the pump off.
- Set the valve to Rinse.
- Turn the pump on and run for about 30 seconds to a minute. Rinsing resettles the bed and flushes remaining dirty water down the waste line.
- Turn the pump off.
- Set the valve back to Filter.
- Turn the pump on and check the pressure gauge. This is your new clean baseline.
Filters with push-pull valves, or different manufacturer instructions, may vary slightly. If your manual differs, follow the manual.
After backwashing
- Recharge DE filters. A DE filter needs a fresh coat of DE after every backwash, usually added through the skimmer. See our guide to DE pool filters for how and how much.
- Top up the pool water. Keep the water at about the middle of the skimmer opening so the pump does not draw air.
- Check the chemistry. If you lost a lot of water, sanitizer and other levels may need adjusting.
- Record the pressure. A simple note on the date and clean pressure helps you spot trends.
How often is too often
Backwashing more than needed wastes water, uses extra power and, in a sand filter, removes some of the fine dirt layer that helps the bed catch smaller particles. It can also let more particles through for a little while after each backwash. In general:
- Avoid backwashing on a fixed schedule if the gauge shows no need.
- Avoid very long backwashes. Once the water runs clear, stop.
- If you find yourself backwashing very frequently, look for the cause. Possible reasons include heavy algae or debris loading, a worn sand bed, or a filter that is too small for the pool.
If pressure doesn’t drop
If the gauge is still well above your baseline after a good backwash and rinse:
- Repeat the backwash once, in case the first run did not clear everything.
- Try a filter cleaner. Oils and scale can bind media. Use a product made for your filter type, following its label.
- Check for a closed valve or blockage in the return line.
- Consider worn media. Old sand or oil-fouled media may need replacing. See our article on how long a pool filter lasts.
- Test the gauge. A stuck gauge can mislead you.
- Look at the pump and plumbing if pressure is oddly high or low. Our pool filter troubleshooting guide covers these checks.
What about cartridge filters?
Cartridge filters have no backwash setting. Instead, you shut off the pump, release pressure, remove the cartridge and rinse it by hand. For sand filter basics, see how a sand pool filter works. For a comparison of all three types, see our overview of pool pumps and filters.