Short answer: it varies a lot, but for a typical single-speed inground pump running 12 hours a day, the electricity can come to a few dollars per day, or very roughly $60 to $150 or more per month, depending on your pump and local rates. A variable-speed pump running at low speed can cost a fraction of that. To get a real number for your pool, you need your pump’s power use and your electricity rate, and both are easy to find.
The formula
Cost = kilowatts × hours × price per kWh
- Kilowatts (kW) is the pump’s power draw divided by 1,000.
- Hours is how long it runs per day (12 here).
- Price per kWh is on your electric bill. Rates vary widely by region, and may differ by time of day.
If you know volts and amps instead of watts, use volts × amps = watts.
Worked examples
These use an illustrative rate of $0.15 per kWh. Your rate will be different, so substitute your own. The power figures are also examples, since real pumps differ.
| Pump (example) | Power draw | Energy for 12 hours | Cost per day | Cost per 30 days |
|---|---|---|---|---|
| Single-speed, about 1 hp class | about 1.2 kW | 14.4 kWh | about $2.16 | about $65 |
| Larger single-speed, about 2 hp class | about 2.0 kW | 24 kWh | about $3.60 | about $108 |
| Variable-speed on low speed | about 0.3 kW | 3.6 kWh | about $0.54 | about $16 |
At a rate of $0.30 per kWh, double all the costs. At $0.10, they would be about two thirds. Published estimates you may see online range widely, partly because they assume different pumps, speeds and electricity rates.
Finding your own numbers
- Read the motor nameplate. It lists volts and amps. For example, a label of 230 volts and 7.5 amps means up to 230 × 7.5 = 1,725 watts, or about 1.7 kW.
- Remember it is a maximum. The nameplate shows the maximum draw. A pump often draws somewhat less once it is running, though it can draw more if the system is restricted or the supply voltage is low.
- Use your electric bill for the rate, and check whether you have tiered or time-of-use pricing.
- Multiply it out with the formula above.
For the most accurate result, a plug-in watt meter or a hardwired energy monitor, installed by an electrician, will tell you what the pump actually uses at each speed.
Does 115V vs 230V change the cost?
Not really. A 230V pump draws about half the current of a 115V pump of the same power, but the wattage, and so the energy you pay for, is about the same. The higher voltage can reduce wiring losses slightly, which is why larger inground pumps often use it.
Ways to lower the bill
- Switch to a variable-speed pump. Power use falls steeply as speed drops, so a pump running at half speed uses much less than half the power. Many owners recover the higher purchase price over time. See variable speed pump settings.
- Run it for fewer hours. Work out the minimum turnover you need rather than defaulting to 12 hours. Our article on how long a pool pump should run shows the math.
- Run it off-peak. If your utility has time-of-use rates, schedule most running in cheaper hours.
- Keep filters clean. A clogged filter raises resistance and makes the pump work harder. See how to clean a cartridge filter and how to backwash a filter.
- Reduce plumbing restrictions. Larger pipes, fewer sharp bends, a larger filter and fewer restrictive fittings all lower the work the pump has to do.
- Right-size the pump. An oversized pump uses more energy than necessary. See what size pool pump you need.
- Keep water balanced. Better water balance and sanitation reduce the need for extra filtration time.
- Consider an energy-efficient motor if you are replacing a worn one.
Is 12 hours even necessary?
Often not. Twelve hours is a common figure, but the right number depends on your pool’s volume and your pump’s flow. A pool that completes a turnover in 6 hours may stay clear with a shorter day, while a larger pool or a pump running slowly may need more. If you are replacing equipment, replacing a pool pump covers what to consider, and the overview of pool pumps and filters shows how the pieces fit together.