Short answer: the process in brief
A green pool is usually an algae bloom, and the usual fix follows the same order each time: remove debris, clean the filter, balance pH, brush every surface, raise free chlorine well above normal (shocking), run the pump continuously, and then vacuum and filter out the dead algae. Expect cloudy water for a while after the green fades. That cloudiness is dead algae, and your filter has to clear it.
How hard this is depends on how dark the water is. Light green or teal water can often be turned around in a few days. A dark, swampy pool can take longer and may need several rounds.
Why pools turn green (and blue-green)
Algae need light, warmth, nutrients and water that isn’t adequately sanitized. Common triggers include:
- Low or inconsistent chlorine. This is the most frequently cited cause.
- Poor circulation or a dirty filter. Dead spots let algae settle and grow.
- Warm weather and strong sun.
- Debris and rain. Leaves, pollen and runoff add nutrients and can bring in algae spores.
- Unbalanced water. High pH makes chlorine less effective.
Blue-green or teal water is often an early bloom, or algae that is partly dying off. It can also be caused by metals such as copper. Treat it like a green pool, but check the next section first.
Algae or metals? How to tell
Not all green water is algae. Two rough clues:
- Murky, cloudy green with slimy surfaces usually points to algae.
- Clear, transparent green (or blue-green) that appeared soon after adding shock or a copper-based product can point to dissolved metals, such as copper from a heater or an algaecide.
If you suspect metals, a pool store test for copper and iron is worth getting, because shocking more won’t fix a metal problem. If the water is green and the walls feel slippery, assume algae.
Before you start
- Get a reliable test kit that measures free chlorine, pH and total alkalinity. Cyanuric acid (stabilizer) is worth testing too, because the more stabilizer in the water, the more free chlorine you need to be effective. Test strips are less precise than drop-based kits.
- Have shock (calcium hypochlorite or liquid chlorine), pH adjusters, a stiff brush suited to your pool surface, a leaf net and a vacuum.
- Wear gloves and eye protection, add chemicals one at a time, never mix different pool chemicals together, and always add chemical to water, not water to chemical. Follow each product’s label.
- Keep swimmers out until free chlorine has come back down to the range your test kit and product labels say is safe.
Step-by-step: cleaning a green pool
- Net out debris. Remove leaves, bugs and floating material. Decomposing debris feeds algae and uses up chlorine.
- Empty the skimmer and pump baskets, then clean the filter. Backwash a sand or DE filter, or rinse a cartridge. A clogged filter can’t handle a bloom.
- Test and balance. Aim for a pH in the 7.2 to 7.6 range before shocking so chlorine works as well as it can. Check total alkalinity, which is commonly targeted at around 80 to 120 ppm.
- Brush everything. Scrub the walls, steps, floor and corners to break up the algae’s protective layer. Use a stainless steel brush only on plaster, gunite or concrete. Use a nylon brush on vinyl, fiberglass or pebble finishes.
- Shock the pool. Add shock according to the label, at dusk or after dark so sunlight doesn’t burn off the chlorine. Pre-dissolve granular products if the label says to, particularly in vinyl pools.
- Run the pump continuously. Keep the filter running 24 hours a day until the water clears. Retest free chlorine regularly, and if it falls to normal levels while the water is still green, shock again.
- Brush again and keep cleaning the filter. Backwash or clean it whenever pressure climbs noticeably above its normal reading.
- Vacuum the dead algae. Once the algae has died and settled, vacuum it out. If your filter has a “waste” setting, vacuuming to waste sends the debris out rather than back through the filter.
- Use a clarifier if needed. If the water stays hazy, a clarifier or flocculant can help the filter catch fine particles. Follow the label, because flocculant has its own steps and can be hard on some filters.
- Retest and rebalance. Once the water is clear, check chlorine, pH, alkalinity and stabilizer again and adjust before swimming.
How much shock?
Pool owners commonly scale the dose with the color of the water: a double dose for light green, triple for darker green, and quadruple for very dark or black-green water. Treat that as a rule of thumb. The actual amount depends on your product’s strength, your pool volume and your stabilizer level, so use the label’s instructions for a standard shock and multiply from there. If you aren’t sure how many gallons your pool holds, work that out first, because guessing is how people under- or over-dose.
Chlorine or algaecide: which kills algae better?
Chlorine is generally the main tool for killing an active bloom. Algaecides are more often used as a follow-up or preventive, and some pool owners use a copper-based or other algaecide alongside shock for stubborn cases. Practices differ, and you should follow the label of whichever product you use. See our guide to how to use algaecide in a pool for timing, types and dosing considerations.
How long does it take for a green pool to clear?
There is no single answer. A lightly green pool with a clean filter and well-balanced chemistry may clear within a few days. A dark green pool may take a week or more, and it can take longer if the filter is struggling, the weather is hot, or the chlorine level keeps dropping. You will usually see the sequence of green, then cloudy blue-gray or white, then clear. Don’t stop treatment at the first sign of cloudiness. That is the stage where the filter does most of the work.
Above ground pool notes
The process is the same, with a few practical differences:
- Small pools use smaller shock amounts, so measure carefully. A pool size chart or your manufacturer’s stated volume helps.
- Use a soft brush on vinyl liners. Never use a steel brush on vinyl.
- Granular shock can bleach or damage a vinyl liner if it settles undissolved. Dissolve it first or use liquid chlorine.
- Many above ground pools have smaller filters, so you may need to clean the filter more often during a bloom.
- Check the waterline and under the skimmer and ladder, where algae often hides.
Does dish soap remove algae?
Dish soap is not a recognized algae treatment. It won’t kill algae, and it can cause foaming and add organic material to the water. Stick to proper chlorine treatment, brushing and filtration.
If the pool stays green, or the algae isn’t green
- If the pool is still green after you shocked it, see why your pool water may be green even after shocking.
- If you see yellow, dust-like algae, see what kills yellow algae in a pool or the longer mustard algae treatment plan.
- If you see dark spots that return after brushing, read how to get rid of black algae in a pool.
- If a drained pool needs a deeper reset, chlorine washing and tile blasting are the heavy-duty options.
Keeping it from turning green again
- Test the water weekly (more often in hot weather) and keep free chlorine consistent.
- Run the pump long enough each day to circulate all the water, and keep the filter clean.
- Brush regularly, especially shaded corners and steps.
- Skim debris promptly and trim back overhanging plants if possible.
- Consider a preventive dose of algaecide if your pool is prone to algae.
- Wash toys, floats and swimsuits that have been in natural water before they go into the pool.