Water Chemistry

Ideal CYA Level for Pool Water and the Chlorine Level That Goes With It

The ideal pool CYA level is usually 30-50 ppm outdoors, but your free chlorine target depends on it. See CYA ranges by pool type and a chlorine-to-CYA table.

On this page
  1. The short answer
  2. CYA targets by pool type
  3. The chlorine level that goes with it
  4. Why more CYA needs more chlorine
  5. Indoor pools
  6. Testing CYA
  7. If your CYA is too low or too high

The short answer

For most outdoor chlorine pools, a commonly recommended cyanuric acid (CYA) level is about 30-50 ppm. Saltwater pools are often run higher, around 60-80 ppm, because the generator produces chlorine continuously. Indoor pools that do not see direct sunlight need little or none, often in the 0-20 ppm range. Check your own equipment manual and local rules, as recommendations differ.

CYA targets by pool type

Pool type Common CYA target
Outdoor chlorine pool About 30-50 ppm
Outdoor saltwater pool About 60-80 ppm (check your generator’s guidance)
Indoor pool About 0-20 ppm
Hot tubs and spas Often not used or kept low. Follow the manufacturer.

CYA does not break down like chlorine, so it builds up over time from tablets, dichlor and added stabilizer. The usual fix for too much is dilution. Some public pool codes cap CYA at a specific value such as 100 ppm. That limit is a ceiling, not a target.

The chlorine level that goes with it

CYA protects chlorine from the sun, but it also slows chlorine’s sanitizing action. The more CYA you have, the more free chlorine you need to keep the same level of protection. A widely used rule of thumb sets the minimum free chlorine at about 7.5% of the CYA level. It is a community guideline rather than a legal standard, and it works best alongside regular testing.

CYA (ppm) Approximate minimum free chlorine (ppm)
20 1.5
30 2.3
40 3
50 3.8
60 4.5
80 6

For reference, the CDC lists a 1 ppm minimum for pools and 2 ppm if a stabilizer is present, which is lower than the table suggests for higher CYA. The table is a more cautious target for pools that carry stabilizer, and it is why a pool with 40 ppm CYA and 1 ppm chlorine can still grow algae even though the chlorine reading looks fine.

To work out how to reach those numbers, see how much chlorine to add to your pool. If you test chlorine and want to understand what each reading means, see free, total and combined chlorine.

Why more CYA needs more chlorine

At any moment, only part of your free chlorine is active. CYA binds some of it. The more CYA there is, the larger the bound share and the smaller the active share, so the same free chlorine reading sanitizes less. That is why adding more stabilizer than needed does not give you better protection, and a pool with very high CYA can suffer algae while testing “OK.”

It is also why very high CYA is described as chlorine becoming “locked,” although it is not fully locked. It is simply working much more slowly. The reading still looks normal, while the effective sanitizing power falls.

Indoor pools

Without direct sun, chlorine is not destroyed by UV in the same way. Indoor pools therefore often keep CYA at a low level or none. Some indoor pools with large windows get enough light to justify a small amount. If you are not sure, a low level is the more cautious approach, since you can add stabilizer but removing it is harder.

Testing CYA

Many pool test strips do not measure cyanuric acid. Check the label, or use a turbidity-based CYA test or a pool store test. Test at least at the start of the season, after refilling and anytime chlorine seems to behave oddly. The reading is a cloudiness-based estimate, so it can be rough, especially at low levels.

If your CYA is too low or too high

For the basics, see pool water chemistry for beginners.

The complete guide to water chemistry

Pool Water Chemistry for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →