Water Chemistry

How Much Chlorine to Add to Your Pool: Dosing by Gallon and Target Level

Work out how much chlorine to add to your pool: find your volume, set a target, then dose liquid chlorine, cal-hypo or dichlor per 10,000 gallons with a worked example.

On this page
  1. Step 1: find your pool volume
  2. Step 2: decide your target free chlorine
  3. Step 3: dose by chlorine type
  4. Worked example
  5. Adding it safely
  6. What the dose does to other chemistry
  7. Retest

Step 1: find your pool volume

Dosing is based on gallons, so start there. These are approximate formulas using average depth in feet and dimensions in feet:

  • Rectangular pool: length x width x average depth x 7.5
  • Round pool: diameter x diameter x average depth x 5.9

Example: a round above ground pool 15 ft across with 4 ft of water is 15 x 15 x 4 x 5.9, or about 5,300 gallons. Irregular shapes are less exact, so check the manufacturer’s stated volume if there is one. If you use a pool store or an app, they use the same logic.

Step 2: decide your target free chlorine

Your target depends on your CYA level and what you are doing:

  • Routine maintenance: often around 1-3 ppm, higher with more stabilizer. See the ideal CYA level and matching chlorine level.
  • Raising chlorine in a pool that dropped to zero: aim for your normal target, then keep testing.
  • Shocking: a much higher level, set by the product label or by your CYA. A pool with more CYA needs a higher shock level.

Test your current free chlorine first. The amount you add is the difference between target and current reading.

Step 3: dose by chlorine type

The table shows approximate amounts to raise free chlorine by 1 ppm in 10,000 gallons. Strengths vary by brand, so use these as estimates and prefer the label.

Product About how much per 1 ppm per 10,000 gal Notes
Liquid chlorine, 12.5% About 10 fl oz No CYA, no calcium
Liquid chlorine, 10% About 13 fl oz Same, weaker
Household bleach, about 8.25% About 15 fl oz Use plain, unscented bleach
Calcium hypochlorite, 65% About 2 oz by weight Adds calcium
Dichlor, 56% About 2.4 oz by weight Adds CYA, about 9 ppm per 10 ppm chlorine
Trichlor tablets Label-based Slow release, acidic, adds CYA

For tablets, a typical starting point is one 3-inch tablet per roughly 5,000-10,000 gallons per week, but it varies. See chlorine tablets, dichlor and why a pool won’t hold chlorine.

Worked example

Pool: 15,000 gallons. Current free chlorine: 1 ppm. Target: 4 ppm. Product: 12.5% liquid chlorine.

  1. Needed increase: 4 - 1 = 3 ppm.
  2. Scale to the pool: 15,000 / 10,000 = 1.5 units.
  3. Dose: 10 fl oz x 3 ppm x 1.5 = about 45 fl oz.

Add roughly 45 fl oz (a little over a third of a gallon). If you are unsure, add about half, circulate, and retest before adding more, since you can always add but not easily remove.

Checking the same pool with cal-hypo 65%: 2 oz x 3 x 1.5 = about 9 oz by weight.

Adding it safely

  • Run the pump and add chlorine near the return jets or by pouring slowly around the pool.
  • Add at dusk or evening if you can, so the sun does not burn off the chlorine right away.
  • Wear gloves and eye protection, and keep products away from acids and from each other.
  • Do not mix chlorine products in one bucket or store them together.
  • Pre-dissolve granular products only if the label says to, and never add water to granules.

What the dose does to other chemistry

Different chlorines change different readings. Cal-hypo adds calcium and raises pH. Liquid chlorine raises pH temporarily. Dichlor and trichlor add CYA, and trichlor lowers pH. See does shocking a pool raise pH and the pool pH guide. If you overshoot, see whether a chlorine level of 10 is safe.

Retest

Wait for the water to circulate, usually a few hours, then test free and total chlorine again. See free, total and combined chlorine to understand why your total reading may stay higher than free. If the chlorine will not hold, the problem is not dose size. See the troubleshooting section in the tablets article above.

For the broader picture, see pool water chemistry for beginners.

The complete guide to water chemistry

Pool Water Chemistry for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →