Water Chemistry

How to Raise and Lower Pool pH

Learn what pool pH is, the target range, and how to raise or lower it safely with soda ash, aeration, muriatic acid or dry acid, plus why pH keeps drifting.

On this page
  1. What pool pH is and the target range
  2. Signs your pH is off
  3. Check total alkalinity first
  4. How to raise pH
  5. How to lower pH
  6. Acid safety
  7. Why pH keeps drifting
  8. Common questions

What pool pH is and the target range

pH measures how acidic or basic water is on a scale where 7.0 is neutral. Pool water is usually kept slightly basic. The commonly cited acceptable range is 7.2 to 7.8, with 7.4 to 7.6 often called the sweet spot for swimmer comfort, chlorine performance and equipment protection.

  • Below about 7.2 is acidic water. It can irritate eyes and skin and corrode metal parts, and it can etch plaster or damage vinyl over time.
  • Above about 7.8 is increasingly basic. Chlorine becomes less effective, calcium can come out of solution as scale, and the water can turn cloudy.

Signs your pH is off

High pH often shows up as cloudy water, scale on tile or equipment, and chlorine that seems to work poorly even when the reading looks fine. Low pH tends to show up as stinging eyes, dry or itchy skin, corroded ladders or fittings, and chlorine that disappears quickly. These symptoms overlap with other problems, so confirm with a test before you add anything.

Check total alkalinity first

Alkalinity is the water’s buffer against pH swings. If it is very low, pH bounces around easily. If it is high, pH tends to drift upward and resists being lowered. A common target is roughly 80-120 ppm. If alkalinity is the real problem, see how to lower the alkalinity in your pool.

How to raise pH

  1. Test pH and total alkalinity and note your pool volume.
  2. Run the pump so the product circulates.
  3. Choose a product:
    • Soda ash (sodium carbonate), sold as “pH increaser” or “pH plus,” raises pH more than it raises alkalinity.
    • Baking soda (sodium bicarbonate) mainly raises alkalinity and raises pH only slightly. Use it when alkalinity is also low.
    • Aeration can raise pH without chemicals. Pointing return jets upward or running a fountain or waterfall releases carbon dioxide, which nudges pH up without adding alkalinity.
  4. Add in small doses. Follow the label, start with about half of what you think you need, and pour it slowly around the pool, or dissolve it first if the label says to.
  5. Wait and retest. Allow a few hours of circulation before testing again, then repeat in small steps if needed.

How to lower pH

Two products are common:

  • Muriatic acid (a diluted form of hydrochloric acid) is liquid, fast and economical but needs careful handling and good ventilation.
  • Dry acid (sodium bisulfate) is a granular product that is generally easier to handle and store, though it is often costlier per treatment.

The general method:

  1. Test pH and alkalinity.
  2. Run the pump.
  3. Measure the dose from the product label or a pool calculator based on your volume and readings. Start with a partial dose.
  4. For liquid acid, follow the label’s dilution advice and always add acid to water, never water to acid. Pour slowly around the deep end, away from metal ladders and lights.
  5. Circulate for several hours, then retest. Repeat in small increments rather than correcting everything at once.

Acid lowers pH and alkalinity together, though not necessarily at the same rate. Overshooting leaves you with acidic water you must then bring back up, so patience pays.

Acid safety

  • Wear chemical-resistant gloves and eye protection, and consider long sleeves and closed shoes.
  • Work outside or in a well-ventilated place and avoid breathing fumes.
  • Never mix acid with chlorine products. The combination can release toxic chlorine gas.
  • Keep children and pets away, and store acid in its original container.
  • Wait for the pump to circulate and for pH to be confirmed in range before swimming. Follow your product label for the exact wait.

Why pH keeps drifting

pH in most chlorine pools tends to rise over time because of carbon dioxide leaving the water, especially with splashing, waterfalls, spas and warm water. Some chemicals also push it around: calcium hypochlorite and liquid chlorine tend to raise it, while trichlor tablets tend to lower it. If you want to know what shocking does to pH, see does shocking a pool raise pH. For how tablets behave, see chlorine tablets and dichlor.

Common questions

Does CYA lower pH? Cyanuric acid is mildly acidic, so heavy use can nudge pH and alkalinity downward, but it is not a pH-lowering tool. Do not use it for that purpose.

Does boiling water change its pH? Not in a way that matters for pool care.

How much muriatic acid at one time? Use the label and a calculator for your pool volume, and add in small doses with a retest between them. Large single doses are risky.

What is the typical pH range for drinking water? Regulators commonly cite roughly 6.5 to 8.5 for drinking water, which is wider than the pool range above. Pool pH is held tighter because it affects chlorine and comfort.

For the broader picture, see pool water chemistry for beginners.

The complete guide to water chemistry

Pool Water Chemistry for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →