How chlorine tablets work
Chlorine tablets (often called pucks) are usually trichlor. They dissolve slowly, releasing chlorine over days, which makes them popular for steady, low-effort sanitizing. Two side effects matter:
- Trichlor is strongly acidic, so it tends to lower pH and alkalinity over time.
- Trichlor contains cyanuric acid (CYA), which stays in the water. Regular use makes CYA climb through the season.
Tablets are a maintenance tool, not a complete system. Many pool pros pair them with periodic shocking or supplemental liquid chlorine, and with regular testing.
How to use tablets safely
- Use a floating dispenser or an in-line or off-line chlorinator. These control how fast tablets dissolve and keep concentrated product away from surfaces. Tie or anchor a floater so it does not rest against a liner or step.
- Do not just throw tablets in the water. A tablet sitting on a vinyl liner or plaster can bleach or damage it.
- Avoid putting tablets in the skimmer basket. When the pump stops, very acidic, concentrated chlorine can sit in the plumbing and damage equipment.
- Do not overfill the dispenser. Overdosing lowers pH sharply and drives chlorine up.
- Handle with dry gloves, keep the container sealed, and never mix tablets with other chemicals or store them next to acids or other chlorine types.
- Follow the product label and your chlorinator’s instructions for loading.
How many tablets
The right number depends on pool size, sun, bather load and CYA. A commonly quoted starting point is one 3-inch tablet per roughly 5,000-10,000 gallons per week, but products and conditions differ, so treat that as a starting point and test. Let your free chlorine reading, not a rule, set the dose.
Also adjust for the pool’s CYA: more stabilizer means you need to hold more free chlorine, as explained in the ideal CYA level and matching chlorine level.
Common questions:
- Do I need to shock if I use tablets? Tablets alone often do not oxidize built-up contaminants, so periodic shocking or supplemental chlorine is common. Test to decide.
- When should I add tablets? Whenever your feeder or floater runs low. Weekly checks suit most pools.
Dichlor: what it is and when to use it
Dichlor (sodium dichlor) is a granular, fast-dissolving chlorine with roughly 55-62% available chlorine. It has a near-neutral pH, so it has much less effect on pH than trichlor. Like trichlor, it contains CYA, so it raises stabilizer as you use it: roughly 9 ppm of CYA for every 10 ppm of chlorine it provides.
Common uses:
- New or freshly filled pools with no stabilizer, where you want chlorine and CYA at the same time.
- Occasional shocking or spot treatment, keeping in mind the CYA it adds.
- Spas and hot tubs, where granular chlorine is widely used. Follow your tub manufacturer’s guidance.
Dichlor is not the same as calcium hypochlorite. Cal-hypo (“cal hypo shock”) does contain chlorine, typically roughly 65-73%, but it has no CYA and adds calcium. Do not mix cal-hypo with dichlor, trichlor or other chemicals.
Regular dichlor or trichlor use is a convenient way to build CYA, but once it reaches your target, many owners switch to unstabilized liquid chlorine to stop it climbing further.
Why your pool won’t hold chlorine
When free chlorine reads zero or drops fast, the cause is usually one of these:
- A test problem. Right after shocking, chlorine can be so high that it bleaches the test reagent and appears to read zero. Dilute the sample (for example 10 parts clean water to 1 part pool water, if your kit’s instructions allow) and retest, then multiply as directed.
- No stabilizer, so sunlight burns it off. Without CYA, direct sun can destroy a large share of free chlorine in a few hours. Even modest CYA helps a great deal.
- High chlorine demand. Algae, bacteria, organic debris, sweat, sunscreen, metals and nitrogen compounds all consume chlorine. If you shock and still test low within hours, demand is probably high.
- High pH. At higher pH, more chlorine stops being protected by CYA and is lost faster in sunlight. Keep pH in range. See how to raise and lower pool pH.
- Chemical conflicts. Some algaecides, especially quaternary ammonium types, and some copper or bromine products can react with chlorine. Check labels.
- Combined chlorine. If most chlorine is tied up as chloramines, free chlorine reads low while total chlorine looks fine. See free, total and combined chlorine.
- Poor circulation or filtration. Dead spots, a dirty filter or a short pump schedule let contamination build.
Fixing it step by step
- Test properly: free chlorine, total chlorine, pH, alkalinity and CYA.
- Correct pH before adding more chlorine.
- Check CYA. If it is low, add stabilizer. See the pool stabilizer guide.
- Clean the filter and brush the pool, and run the pump longer while you work on it.
- Raise chlorine in a measured way. How much chlorine to add to your pool shows how to dose. A pool with real chlorine demand may need chlorine held at a higher level until it stops dropping overnight.
- Retest the next morning. A big overnight loss means demand is still high.
A pool can look clear and still have no chlorine, because bacteria are invisible and algae may not yet be visible. Zero chlorine means the water is not being sanitized, so avoid swimming until you have measured chlorine.
Switching away from stabilized chlorine
If CYA is above your target, stop using tablets and dichlor and use liquid chlorine or cal-hypo instead. See how to lower cyanuric acid without draining the whole pool for what else you can do.
For the bigger picture, start with pool water chemistry for beginners.