Water Chemistry

How to Raise Calcium Hardness in Pool Water

Low calcium hardness makes pool water aggressive. Learn target ranges, how much calcium chloride to add per 10,000 gallons, and how to add it without clouding the water.

On this page
  1. What calcium hardness is and why it matters
  2. Target ranges by pool surface
  3. Test first, including your fill water
  4. How much calcium chloride to add
  5. How to add it
  6. Does shocking a pool raise calcium hardness?
  7. If hardness is too high instead
  8. Hot tubs

What calcium hardness is and why it matters

Calcium hardness (CH) measures the dissolved calcium in your water. It is one of the slower-moving numbers in a pool, but it matters for two opposite reasons:

  • Too low and the water becomes aggressive. It tends to pull calcium from whatever it can reach, which can etch or roughen plaster, pit grout and corrode metal parts such as heater components.
  • Too high and calcium can come out of solution, leaving white scale on tile, in plumbing and on heaters, and sometimes causing cloudy water.

So the goal is a balanced middle range, not the highest or lowest possible number.

Target ranges by pool surface

Commonly cited ranges, which your surface manufacturer or builder may refine:

Pool type Typical calcium hardness
Plaster or concrete About 200-400 ppm (250-350 is often preferred)
Vinyl liner About 150-250 ppm
Fiberglass About 150-250 ppm
Spas and hot tubs About 150-250 ppm, lower end if the water is hot

Plaster needs more because the water can otherwise draw calcium from the surface. Vinyl and fiberglass have no calcium to lose, but very soft water can still corrode metal fittings and equipment.

Test first, including your fill water

Use a reliable test. Many test strips are rough on hardness, so a liquid titration kit or a pool store test gives you a more dependable number. If your hardness keeps falling after you add calcium, test your tap or well water as well. Very soft fill water, or lots of rain and water replacement, will keep diluting your calcium.

How much calcium chloride to add

Calcium hardness increaser is calcium chloride. Strengths vary by product, so check the label. As a common rule of thumb for typical products, about 1.25 lb per 10,000 gallons raises hardness by roughly 10 ppm.

A worked example for a 10,000 gallon pool:

  • Current hardness: 120 ppm. Target: 200 ppm. Needed rise: 80 ppm.
  • 80 ppm is eight steps of 10 ppm, so about 8 x 1.25 lb = 10 lb.

Because that is a lot at once, many manufacturers suggest splitting large corrections over more than one day, and a product label may set a per-dose limit. Use your actual pool volume and the product’s own chart in preference to this estimate.

How to add it

  1. Run the pump to circulate water.
  2. Wear gloves and eye protection. Calcium chloride releases heat when it dissolves.
  3. Add as the label directs. Some products say to broadcast granules over the deep end. Others say to pre-dissolve in a bucket of water. If you dissolve it, add the calcium to the water slowly, never the other way around, and use a sturdy container because it warms up.
  4. Brush any granules that settle on the floor so they dissolve and do not damage the surface.
  5. Circulate for several hours, then retest. Retest again after a day if you added a large amount.

Avoid adding soda ash or baking soda at the same time. Concentrated calcium and carbonate can combine and form a cloud of fine particles. Wait and add other adjustments separately. For pH and alkalinity, see the pool pH guide.

Does shocking a pool raise calcium hardness?

It can, depending on the product. Calcium hypochlorite (“cal-hypo”) shock adds calcium along with chlorine. Over a season of regular use, that accumulates, and it can be enough to nudge a soft pool upward. Liquid chlorine, dichlor and non-chlorine shock do not add calcium in the same way. If your hardness is already high, switching away from cal-hypo can slow the climb. For how different shocks affect other chemistry, see does shocking a pool raise pH.

If hardness is too high instead

Chemicals do not remove dissolved calcium. The reliable approach is dilution: replace part of the pool water with softer fill water, which only works if your source water is lower in hardness than the pool. Some pool services offer reverse osmosis. Be cautious about draining, since lowering the water level in some pools can risk damage to liners or shells, and check with a pool professional if unsure. A sequestering product can help manage scale in the short term without lowering the reading.

Hot tubs

Spa water is warm, which encourages scale, and spas have heating elements that suffer from it. Aim toward the lower end of the spa range and check your tub manufacturer’s guidance, since tub materials and sanitizers vary.

For the full set of numbers to track, see pool water chemistry for beginners.

The complete guide to water chemistry

Pool Water Chemistry for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →