Short answer
If the water is still green after shocking, either the shock didn’t kill all the algae, or the green isn’t algae at all. The most common causes are too little chlorine for the amount of algae, high pH or high stabilizer (cyanuric acid) making chlorine less effective, a filter or pump that isn’t clearing the water, or dissolved metals. A test kit tells you which of these applies.
Is it normal for the pool to stay green for a while?
Somewhat, yes. After a proper shock, a bloom typically goes through stages: green, then cloudy gray-blue or white as the algae dies, then clear once the filter has removed the dead material. If the water has not changed at all after a day or two, or turns green again as the chlorine level drops, then the treatment isn’t working. A large bloom can also take more than one round. Our guide to cleaning a green pool has the full process and expected timeline.
Common reasons the water is still green
Not enough chlorine for the amount of algae
A routine maintenance dose of shock won’t clear a heavy bloom. Pool owners often scale the dose with the color of the water: double for light green, triple for dark green and quadruple for very dark water. Check your product’s label, and calculate your pool’s volume accurately. If chlorine is falling back to normal levels while the water is still green, the algae has used it up and you need to shock again.
High pH
Chlorine becomes less effective as pH rises, and a pH above about 7.6 is commonly cited as a point where it starts to lose strength. Test and adjust pH before shocking where you can, with a target of roughly 7.2 to 7.6.
High cyanuric acid
Cyanuric acid (stabilizer or CYA) protects chlorine from sunlight, but a high level reduces how well the chlorine works, so you need more free chlorine to do the same job. Some pool owners and test-kit guides use a chart that ties the free chlorine needed to the CYA level. Regular use of stabilized products (trichlor tablets, dichlor shock) raises CYA over time. Test CYA with a proper kit. If it is very high, the usual fix is to partly drain and refill with fresh water, since CYA doesn’t break down on its own.
The shock wasn’t the right kind or was applied badly
- Chlorine breaks down in strong sunlight, so shock at dusk or after dark.
- Make sure the product is actually a chlorine shock. Some “non-chlorine” or oxidizer shocks aren’t meant for killing a bloom.
- Granular shock should be dissolved or distributed as the label says.
- Skipping the brush leaves algae protected on surfaces. Brush before and after shocking.
Filter and circulation problems
A dirty filter and an under-run pump let algae and chlorine-demand sit in the water. During treatment, run the pump continuously and clean or backwash the filter as pressure climbs. Check the skimmer and pump baskets and that the return jets are pushing water in all areas. Algae can also stay inside the filter itself.
Metals instead of algae
Clear, bright green or blue-green water that appeared after adding shock or a copper-based algaecide may be dissolved metals such as copper or iron being oxidized. This is a different problem. Extra shock won’t clear it, and may make it worse. A pool store can test for metals, and a metal-sequestering product (or a professional’s advice) is the usual route. If you see a clear green or blue-green tint and the walls are not slimy, test for metals before shocking again.
Phosphates and constant new nutrients
Phosphates can feed algae, and some sources cite them as a reason algae keeps returning. Keeping chlorine at the right level matters more than chasing phosphates alone, but if algae returns repeatedly, a phosphate test is a reasonable step. Also look for sources of nutrients, such as leaf litter, runoff, fertilizer and nearby plants.
Quick diagnosis table
| What you see | Likely cause | First thing to check |
|---|---|---|
| Murky green, slippery walls | Active algae bloom | Free chlorine, pH, CYA |
| Chlorine disappears quickly | Heavy chlorine demand | Retest and shock again |
| Chlorine reads fine but water stays green | High CYA or high pH | CYA and pH |
| Clear green or blue-green, not slimy | Metals | Copper and iron test |
| Cloudy but no longer green | Dead algae in the water | Filter and clarifier |
| Green returns within days | Poor circulation or filter | Pump run time, filter condition |
What to do next
- Test free chlorine, pH, total alkalinity and cyanuric acid, and consider a metals test if the water is clear green.
- Adjust pH first if it is high.
- Brush every surface.
- Shock at dusk with a dose appropriate for the depth of green, according to the product label.
- Run the pump continuously and clean the filter as needed.
- Retest each day and shock again if chlorine drops before the water clears.
- Vacuum out dead algae once it has settled, and use a clarifier if the water stays hazy.
If you plan to add algaecide afterwards, read how algaecide is used and timed. If the color isn’t green but yellow or dark, see yellow algae and black algae.
When to get help
If the water remains green after several rounds of treatment with good chemistry and a clean filter, take a water sample to a pool store, or ask a local pool service to test it. They can check for metals, stabilizer and equipment problems that are hard to diagnose at home.