Algae and Green Water

Deep Cleaning Pool Surfaces: Chlorine Washing and Tile Blasting

Learn when a chlorine wash or pool tile media blasting makes sense, how each works, the safety cautions and when to hire a professional.

On this page
  1. What these two methods are for
  2. Chlorine wash
  3. Pool tile blasting
  4. DIY or hire a professional?

What these two methods are for

Regular brushing, shocking and filtering handle most algae and dirt. A chlorine wash and tile blasting are for problems those routine steps can’t fix:

  • A chlorine wash sanitizes and lightens a surface after severe algae, usually in a pool that has been drained.
  • Tile blasting (media blasting) removes hard mineral scale, commonly calcium, from waterline tile without draining the whole pool.

Both are heavier-duty than normal maintenance. If your pool is simply green, start with our guide to cleaning a green pool.

Chlorine wash

When it’s used

A chlorine wash is generally considered when a drained plaster pool has heavy algae, a swampy bloom, or persistent black or other stubborn algae that normal shocking didn’t clear. It targets organic growth and stains, not mineral scale or metal stains.

Chlorine wash versus acid wash

An acid wash uses diluted acid and removes a thin layer of the plaster surface, which is why it is more aggressive. A chlorine wash sanitizes the surface without removing plaster, so it is generally seen as the gentler option. They suit different problems. Chlorine is for organic growth, and acid is for mineral deposits and some metal stains.

Never mix chlorine and acid, or apply one right after the other, without rinsing thoroughly and following professional guidance. The reaction can release toxic chlorine gas.

How a chlorine wash is done

The general sequence described by pool professionals is:

  1. Drain the pool (see the cautions below) and turn off the equipment.
  2. Put on protective gear. That means eye protection, gloves, protective clothing and, for strong fumes, a suitable respirator.
  3. Dilute liquid chlorine with water. Dilution ratios vary between sources and with how severe the problem is, so confirm the mix with a pool professional or the product label rather than guessing.
  4. Apply from the top down. Work from the upper walls toward the floor, keeping the surface evenly wet.
  5. Let it sit and scrub. Give it some minutes to work, and scrub stubborn spots with a brush suitable for the surface.
  6. Rinse thoroughly and pump out the wastewater. Don’t let chlorinated water dry on the surface.
  7. Refill, clean or replace filter media as needed, and rebalance the water before anyone swims.

Safety and drainage cautions

  • Draining isn’t always safe. In areas with a high water table, an empty in-ground pool can be pushed upward by groundwater, which can crack or lift the shell. Vinyl liners can shrink or wrinkle when left empty, and fiberglass pools can be damaged too. Check with a pool professional or the pool’s builder before draining.
  • Wastewater rules. Chlorinated water often can’t be discharged into storm drains, streets or natural waterways. Local rules vary, so check them first.
  • Ventilation and PPE. Work with plenty of fresh air. Chlorine fumes and splashes are hazardous.
  • Keep children and pets away while chemicals are in use.

Can you clean a pool without draining it?

Often, yes. For ordinary algae, brushing, a heavy chlorine shock, running the filter continuously, vacuuming and a clarifier can restore a pool with the water in place. See our guides on green pools and black algae. Draining and a chlorine wash are for severe cases.

Pool tile blasting

Why tile gets scale

Hard water leaves calcium carbonate deposits at the waterline as water evaporates. It can form a white or gray crust that ordinary brushing doesn’t remove, and over time it can be hard to get off without abrasive cleaning.

Media types

Blasting uses a fine material propelled at the tile at low pressure. Common types include:

  • Glass bead. Round glass particles that lift scale without cutting into glazed tile in the hands of an experienced operator.
  • Soda (sodium bicarbonate). Softer and often used on more delicate surfaces. Some contractors note that it can raise the water’s pH and alkalinity.
  • Kieserite (a magnesium sulfate mineral). Water-soluble and described as pH-neutral, so it dissolves over time and is considered gentle on surroundings.
  • Coarser abrasives. These are used selectively on natural stone, but they are generally too aggressive for standard glazed tile.

How the process works

A typical job, as described by tile cleaning contractors:

  1. The water level is lowered a few inches below the calcium line, so the whole pool does not need to be emptied.
  2. The operator blasts the tile at low pressure, holding the nozzle at a consistent distance and angle.
  3. The tile is rinsed, and the media and scale are vacuumed out of the pool. Water-soluble media may dissolve or pass through the filter.
  4. Many jobs take from one to a few hours for an average-size pool, depending on the amount of buildup.

Can you sandblast pool tile?

Traditional sand blasting is generally too aggressive for pool tile and can etch glaze or damage grout. What is usually called “sandblasting” tile in the pool trade is gentler media blasting with glass bead, soda or kieserite. Stick with those and with a contractor who has experience on your tile type.

How much does it cost?

Prices vary by region, tile type, how bad the buildup is and the size of the waterline. Contractors often quote per linear foot of tile or by the job. Get at least two quotes and ask what media they use.

Gentler DIY options

For light scale, there are options to try first:

  • A pumice stone or tile-cleaning stone for small areas, used gently. Removing waterline scum and calcium covers the technique. Test a hidden spot, since abrasives can scratch some tile and glass tile in particular.
  • A pool tile cleaner product, following the label.
  • Regular brushing of the waterline and keeping calcium hardness and pH balanced to reduce how fast scale forms.

DIY or hire a professional?

A chlorine wash involves draining, strong chemicals and wastewater rules, so many owners prefer to hire a pool professional. Tile blasting needs equipment and technique, and an inexperienced operator can damage tile. If the problem is only algae that returns, you may be better off improving routine care, or starting with the options in our guide to using algaecide, before taking on a surface deep clean.

The complete guide to algae and green water

How to Clean a Green Pool
Read the guide

Keep exploring

Guides from other topics

All topics →