Algae and Green Water

How to Get Rid of Black Algae in a Pool

Black algae is stubborn. Learn how to scrub, shock and treat it on plaster, vinyl and fiberglass pools, and how to stop it coming back.

On this page
  1. What black algae is
  2. Why it’s so hard to remove
  3. What you’ll need
  4. Step-by-step treatment
  5. Treating black algae by surface type
  6. If it keeps coming back
  7. Preventing black algae

What black algae is

Black algae shows up as dark blue-black or black spots, often raised or crusty, on pool walls, floors, steps and in grout lines. Although it is called an algae, it is generally described as a type of cyanobacteria with layered, protective growth. The visible spots sit on top, and on rough surfaces such as plaster or gunite it can anchor itself into tiny pores.

Why it’s so hard to remove

  • A protective outer layer. Normal chlorine levels struggle to get through it, so brushing to break the layer open is a key step.
  • It anchors into porous surfaces. Plaster, gunite and grout hold it better than smooth surfaces.
  • It hides. It survives in poorly circulated spots, and spores can sit in the filter or on equipment.
  • It’s slow to treat. Treatment usually takes more than one round, spread over several days.

What you’ll need

  • Test kit (free chlorine, pH, alkalinity, ideally cyanuric acid).
  • The right brush for your surface (see below).
  • Chlorine shock, calcium hypochlorite or liquid chlorine, according to the label.
  • A black algae treatment or an algaecide labeled for black algae.
  • Eye protection, gloves and clothing that you don’t mind getting splashed.

Step-by-step treatment

  1. Clean the filter. Backwash or clean it so water flows well and circulation is strong.
  2. Test and balance the water. A pH around 7.2 to 7.6 helps chlorine work, and total alkalinity is often targeted at 80 to 120 ppm.
  3. Brush every spot hard. Scrub each dark patch to break open the protective layer, and brush surrounding areas too, as growth you can’t see may be next to it.
  4. Shock heavily. Many guides recommend a very high dose, sometimes called a quadruple shock, applied at dusk. The exact amount depends on your product and pool volume, so follow the label and calculate your pool’s gallons carefully.
  5. Treat with a black algae product. After shocking and brushing, apply an algaecide labeled for black algae (copper-based formulas are common) and follow the label. Copper can stain some surfaces, so be careful, especially on light-colored finishes and vinyl.
  6. Run the pump continuously. Keep the filter running for at least a day, brushing the affected areas again a few times during that period.
  7. Clean the filter again and vacuum the dead material, to waste if possible.
  8. Repeat if needed. If spots return or only fade, repeat the cycle in a few days. Stubborn cases can take several rounds.
  9. Retest and rebalance once the spots are gone.

Treating black algae by surface type

  • Plaster, gunite or concrete: A stainless steel brush is commonly used because the surface is hard. Be firm but don’t gouge.
  • Vinyl liner, fiberglass or pebble finishes: Use a nylon brush only. Steel bristles can scratch and damage these surfaces.
  • Direct tablet contact: Some owners rub a piece of chlorine tablet on a spot on plaster. Concentrated chlorine can bleach or damage vinyl and other finishes, so avoid this on vinyl or fiberglass and don’t leave tablets sitting on any surface.
  • Grout lines and tile: Brush carefully. Black algae in grout can be a reason to consider a deeper clean.

If it keeps coming back

  • Check circulation and filter. Dead spots and a dirty filter let algae survive.
  • Check chlorine consistently. Low or intermittent chlorine, high pH or high stabilizer reduce effectiveness. A free chlorine level around 2 to 4 ppm is commonly suggested after treatment, but the appropriate level depends on your stabilizer, so check with a pool store.
  • Sanitize gear. Swimsuits, floats and equipment from natural waters or from other pools can bring it in.
  • Consider a deeper cleaning. In a drained plaster pool, a chlorine wash is sometimes used for persistent black algae. Check the safety cautions in that article first, and talk to a pool professional before draining.

For more on routine algae control, see our guides to cleaning a green pool and using algaecide.

Preventing black algae

  • Test the water weekly and keep free chlorine and pH in range.
  • Brush walls, floors and steps regularly, especially shaded or low-flow spots.
  • Run the pump long enough each day to circulate the whole pool, and keep the filter clean.
  • Rinse and dry gear that has been used in natural water before it goes into the pool.
  • Treat the first small spot early, since small patches are easier to remove than established ones.

The complete guide to algae and green water

How to Clean a Green Pool
Read the guide

Keep exploring

Guides from other topics

All topics →