What mustard algae looks like
Mustard algae, also called yellow algae, appears as a yellow, tan or brown dusty film. It is often mistaken for sand, pollen or dirt on the pool floor and walls, and it tends to show up in shaded areas. It wipes or brushes off easily, but it comes back quickly if the spores aren’t killed.
For a short answer about which products and methods work, see what kills yellow algae in a pool. This article is the fuller plan, from treatment through aftercare.
Why mustard algae is so persistent
- It resists normal chlorine levels. A routine dose often doesn’t clear it.
- It hides. Spores stay in the filter, on shaded surfaces, behind ladders and around light niches.
- It travels on gear. Swimsuits, towels, toys, floats, brushes and pool cleaners can all carry it, and it can reinfect the pool after you have treated the water.
- It’s helped by warm weather and debris, poor circulation and inconsistent chlorine.
Supplies
- Test kit for free chlorine, pH, total alkalinity and cyanuric acid.
- Stiff brush suited to your surface (stainless steel only on plaster, gunite or concrete; nylon on vinyl, fiberglass or pebble finishes).
- Chlorine shock (calcium hypochlorite or liquid chlorine).
- A yellow algae treatment or algaecide labeled for mustard algae, if you choose to use one.
- Bleach and a bucket for cleaning tools, and laundry detergent for swimwear.
- Gloves and eye protection. Never mix chemicals.
Step-by-step treatment plan
- Deal with gear first. Remove toys, floats and accessories. Wash swimsuits and towels in the washing machine. Soak or wipe brushes, poles, vacuum heads, hoses and cleaners with a dilute bleach solution, rinse well and let them dry. Check what each item is made of before using bleach.
- Clean the filter. Backwash a sand or DE filter, or rinse a cartridge, so circulation is good. Turn the pump on and keep it running for the whole treatment.
- Test and balance. Adjust pH toward the middle of the normal range, about 7.2 to 7.6, so chlorine works well. Total alkalinity is often targeted at 80 to 120 ppm. Check stabilizer, as high levels reduce chlorine effectiveness.
- Brush everything. Scrub floor, walls, steps, corners, behind ladders, around lights and skimmers, and anywhere shaded. Brushing breaks the algae’s hold and moves it into the water so chlorine can reach it.
- Add a yellow algae treatment if you use one. Some products are added before shocking, and one retailer’s guide suggests a short wait before the shock goes in. Follow the label’s dose for your pool volume.
- Shock in the evening. Commonly recommended is a triple dose of shock, repeated if needed. One retailer’s guide spaces three doses at least 12 hours apart. The amount depends on the product and your pool’s gallons, so use the label and calculate volume carefully.
- Keep chlorine up. Retest free chlorine and top up if it falls while algae is still visible. Letting it drop gives the algae a chance to recover.
- Clean the filter again. After the final dose has circulated, turn off the pump, then backwash or clean the filter, since spores and dead algae collect there.
- Vacuum and clarify. Vacuum dead algae, to waste if your filter allows. A clarifier can help with leftover haze. Wait until chlorine is below the level the clarifier label specifies.
- Retest and rebalance before swimming. Don’t swim until free chlorine has come back down to a safe range.
After treatment: confirm it’s gone
Brush the shaded spots again over the next few days and look for yellow dust. If any returns, repeat the shock cycle and check that all gear has been cleaned. It isn’t unusual to need two rounds.
Why it comes back
- Gear or swimwear that wasn’t cleaned.
- A filter that still holds spores.
- Low-circulation, shaded corners that weren’t brushed.
- Inconsistent chlorine or high pH.
- Debris and runoff after storms or from nearby trees.
How to keep mustard algae from returning
- Test weekly and keep free chlorine, pH and alkalinity in range. The right chlorine level depends on your stabilizer.
- Run the pump for enough hours each day, and keep the filter and baskets clean.
- Brush weekly, especially shaded walls, steps and corners.
- Shock periodically, such as after heavy use, storms or hot spells, as the product label recommends.
- Consider a preventive algaecide. See how to use algaecide in a pool for types and timing.
- Clean anything coming from natural water (lakes, oceans, other pools) before it goes in.
- Trim vegetation near the pool and skim debris promptly.
If your water is green or dark rather than yellow, see our guides to cleaning a green pool and black algae removal.