Signs the return line is leaking
The return line carries filtered water from the equipment back to the pool, and it is under pressure whenever the pump runs. Common signs of a leak:
- The pool loses more water when the pump is running than when it is off
- Wet, soft or sunken ground along the pipe route, or an unusually green patch of lawn
- Pressure at the returns that seems weaker than before
- Air bubbles or dirt coming from the return jets
- Water pooling near the equipment pad or where the pipe passes under a deck
Confirm it is the pipe first
Several different leaks produce the same symptom, so rule out the other sources before you dig. Do a bucket test, then compare water loss with the pump on and off, as described in losing water in an inground pool. Check the equipment pad for dripping unions, valves and pump fittings, and inspect the return fittings in the pool wall.
If the leak is underground and you cannot locate it, a leak-detection company can pressure test the line and pinpoint the break, which can save a lot of digging.
Repair options
- Replace a damaged section with new pipe and couplings. This is the standard repair for a crack or broken joint. Cut out the damaged piece and glue in new pipe with couplings.
- Use a slip (repair) coupling. A slip coupling has no internal stop, so you can slide it over a gap, which makes it easier to fit into an already-installed line that cannot move much. This is often used when the pipe cannot be flexed apart.
- Replace a damaged fitting. If the leak is at an elbow or tee, you may only need to replace the fitting.
- Leave it to a professional. If the line is under a deck, concrete or a pool, it may need a contractor.
Quick patches such as epoxy putty or leak-sealing products are sometimes used on small pinholes, but they are generally temporary on a pressurised line. Treat them as a stopgap.
Step-by-step: replacing a section
You will need a pipe cutter or fine-toothed saw, a deburring tool or knife, PVC primer and cement suited to the pipe, replacement pipe and couplings of the correct size, and a rag.
- Turn off the pump at the breaker and close the valves so that water is not feeding the section you are working on.
- Expose the pipe and dig around it so you can work without straining it. Support the pipe so it does not sag.
- Drain the line as best you can. PVC cement works best on a dry joint.
- Cut out the damaged part, making square cuts on solid pipe, well beyond the visible crack.
- Deburr and chamfer the ends. A light bevel on the cut edge helps cement spread into the joint rather than being pushed out by the pipe. A forum contributor with a pool-pipe repair recommended this step.
- Dry-fit the new pipe and couplings to make sure everything lines up and the pipe seats fully.
- Prime and cement: apply primer to the pipe end and the inside of the fitting, then apply cement, push the pieces together with a quarter turn, and hold for a few seconds. Follow the cement manufacturer’s directions for set and cure times.
- Wait for the full cure time before pressurising. This can be longer in cold or damp conditions.
- Test before backfilling. Run the pump and watch the joints for weeping. Only fill the trench once you are satisfied it is dry.
Working with wet pipe
Standard PVC cement does not bond well to wet surfaces, and a joint made on wet pipe is more likely to fail. Pipe can be dried with rags, and some products are marketed for damp conditions, but the safest approach is to drain and dry the pipe as much as possible, or use a mechanical coupling that does not rely on cement. Read the label of whatever product you use.
For the basics on pipe types and sizes, see what type of PVC is used for pool plumbing. Using the wrong material, for example a thin-walled pipe, can lead to repeated failures.
Causes of return line leaks
- Tree roots pushing against pipes and fittings
- Ground movement, settling or erosion under the pipe
- Freezing water in lines that were not drained or protected
- Poor original joints or poor support
- Impact damage from digging or equipment
If the cause is still there, the repair will not last. In the forum example mentioned above, removing the tree and root that were pushing on the pipe was part of the fix.
When to hire a professional
Call a professional if the leak is under a deck or concrete, if you cannot find the break, if the pipe is deep or in unstable soil, or if repairs seem to keep failing. Pressure testing and leak locating are specialised, and a professional can also check for more than one leak in the same line. For a sense of what repairs can cost, see is it expensive to fix a pool leak. For the larger picture of how the lines connect, see the pool plumbing overview.