Plumbing and Leaks

Losing Water in an Inground Pool: Finding the Leak

How to tell evaporation from a leak in an inground pool, narrow down the source with simple tests, and decide what to do next.

On this page
  1. Normal water loss vs a leak
  2. Start with the bucket test
  3. Narrow it down: pump on vs pump off
  4. Where inground pools usually leak
  5. Clues from the level itself
  6. Finding the exact spot
  7. What to do next
  8. What it costs

Normal water loss vs a leak

Every outdoor pool loses some water. Evaporation is the biggest part, and it depends on temperature, wind, humidity, sun and whether you use a cover. Splashing, backwashing and swimmers also take water out. Competitor sources quote everything from about 1/8 inch to 1/4 inch a day as normal, and some allow a bit more in hot, windy climates. A rough rule is that a drop of more than about a quarter inch a day, or a loss that does not follow the weather, is worth investigating.

Signs that point toward a leak rather than evaporation:

  • You need to add water regularly, even in cool or calm weather
  • The water level keeps falling when it is cloudy, cold or humid
  • Wet or soft patches, or unusually green grass, near the pool or equipment
  • Air bubbles at the return jets or in the pump basket
  • Cracked tile or coping, or gaps around the deck
  • A higher-than-normal water bill if you have an automatic fill

Start with the bucket test

The simplest first step is the bucket test. It compares the drop in your pool with the drop in a bucket of pool water that is exposed to the same weather. If the pool drops more than the bucket, evaporation alone does not explain the loss.

Narrow it down: pump on vs pump off

Once you have confirmed a leak, you can learn a lot by comparing water loss with the pump running against the pump off. Repeat the bucket test for a full day each way, ideally in similar weather and with no rain:

  • More loss with the pump running suggests a leak on the pressure side, such as a return line, a heater or filter fitting.
  • More loss with the pump off suggests a leak on the suction side, such as a skimmer or main drain line, or in the pool shell.
  • About the same loss either way often points to a leak in the shell, liner or a fitting in the pool wall rather than in the plumbing.

These results are indications, not proof, since the two tests happen on different days with different weather. They are still useful for giving a leak-detection technician a starting point.

Where inground pools usually leak

  • Skimmer: the seal where the skimmer meets the pool wall, cracks in the body, or leaks where the pipe connects at the bottom
  • Return fittings and lines: loose or cracked fittings, or damage to the pipe behind them
  • Pool lights: the conduit that carries wiring from the light niche is a known weak spot
  • Main drain and suction lines: harder to see, usually found by pressure testing
  • Equipment pad: pump seals and lid o-rings, valves, unions, filter fittings and heater connections. See what to do when a pool pump is leaking
  • Shell, plaster or liner: cracks in concrete or plaster, tears or pinholes in a vinyl liner, or loose liner around fittings
  • Underground plumbing: damage from shifting soil, roots or freezing

Clues from the level itself

Notice where the water stops falling. If the level drops quickly and then stops at a particular height, such as the bottom of the skimmer opening, a light or a step, the leak is often near that height. Many pool pros use this as a starting point for where to look. If it falls to the bottom of the skimmer and stops, check the skimmer and the plumbing around it. If it keeps falling past all fittings, look at the shell, floor or deeper plumbing.

Finding the exact spot

  • Visual checks. Look at the skimmer throat, return fittings, light niche, steps and any visible tile or liner damage. Check the equipment pad while the pump is running.
  • Dye test. With the pump off and the water still, release a small amount of dye near suspected spots and watch whether it is pulled toward a crack or gap. See finding a pool leak with dye for the method.
  • Pressure testing and electronic detection. Underground pipes are usually tested by a leak-detection professional, who plugs lines and checks if they hold pressure, or uses listening equipment.

What to do next

Avoid letting the pool drop below the skimmer for long, since the pump can run dry and be damaged. In some soils, large changes in water level can also put stress on the pool shell, so if the pool is draining quickly, shut the pump off and get advice.

What it costs

Costs vary a lot with the cause and where you live. Our article on whether it is expensive to fix a pool leak covers what tends to drive the price.

For how all of the parts connect, see our pool plumbing overview.

The complete guide to plumbing and leaks

Pool Plumbing System: Parts and How Water Flows
Read the guide

Keep exploring

Guides from other topics

All topics →