Plumbing and Leaks

Finding a Pool Leak With Dye: Step-by-Step Method

How to use leak-finding dye to locate a leak in a pool liner, fittings, skimmer or light niche, plus what it means when the dye finds nothing.

On this page
  1. What a dye test can and cannot find
  2. What you need
  3. Prepare the pool
  4. Step by step
  5. Where to test
  6. Reading the dye
  7. If the dye finds nothing
  8. After you find it

What a dye test can and cannot find

A dye test shows you water moving through a small opening. If you release a little dye next to a hole, crack or gap that is leaking, the escaping water draws the dye in, and you see a thin stream of color pulled toward and into the defect.

It works best for leaks that you can reach: pinholes and tears in a vinyl liner, cracks in plaster or fibreglass, loose liner around fittings, gaps around the skimmer or light, and cracks near steps.

It does not find leaks in buried pipes, because dye in the pool only tests what water is passing through at the spot where you place it. A leak in an underground line is usually found by pressure testing or electronic detection, which a leak-detection professional can do.

What you need

  • Leak-finding dye, or a similar pool-safe dye made for the purpose. Some people use a dye bottle or a syringe-style applicator
  • Goggles or a mask and snorkel, so that you can see clearly at the surface of the wall
  • A flashlight if the light is poor
  • Patience, and still water

Use the dye according to the product’s directions, and avoid mixing different chemicals or products in the water.

Prepare the pool

  1. Run a bucket test first if you have not already. See the bucket test. There is no point searching for a leak if evaporation explains the drop.
  2. Turn off the pump and any water features and cleaners, and wait for the water to settle. Moving water makes the dye hard to read.
  3. Keep swimmers out of the water while you work, and move slowly so that you do not create currents.
  4. Look first. Check the liner for visible tears, wrinkles, bulges or places where it has pulled away from the wall, and look at fittings for gaps.

Step by step

  1. Get as close to the area you are checking as is safe, with your face near the surface of the wall.
  2. Release a small amount of dye slowly, about an inch or two from the suspected spot. Do not squirt it straight at the surface, since pressure from the bottle can mimic suction.
  3. Watch the dye for a minute or so. If the dye is drawn into a crack or hole, or visibly streams toward it, you have found the spot.
  4. If nothing happens, move to the next spot. Work your way around the pool systematically.
  5. Note the location, such as by marking the pool wall at the waterline with tape, or making a note of the depth and a nearby reference.

Where to test

  • Skimmer throat and faceplate, including the screws and gasket
  • Return fittings, the eyeball and the area around them
  • Light niche and conduit area
  • Steps and corners, including where steps meet the wall
  • Liner seams, wrinkles and folds
  • Main drain cover and its surround
  • Any visible cracks or tears, and the area around any previous patches

If the water level stopped dropping at a particular height, concentrate on that height first. Many leaks sit near the point where the level stops. See losing water in an inground pool for how to use that clue.

Reading the dye

  • Dye drifts away slowly with the water: normal movement, no leak at that spot.
  • Dye is pulled quickly and straight into a gap: likely a leak.
  • Dye stays in a cloud: no suction there.

Be careful with deep water and hard-to-reach places. If the leak seems to be at a spot you cannot reach safely, a professional diver or leak-detection company can help.

If the dye finds nothing

This is common, and it does not mean there is no leak. The leak might be:

  • In an underground pipe, or behind a fitting
  • In a spot that is too small for dye to show up
  • In a place you did not reach
  • Under or behind a loose liner, where air and water can move around without any clear suction at the surface, which can happen around fittings where the liner has come loose

A forum case involved a liner pool losing a large amount of water where multiple dye tests did not find the leak and the liner around fittings was loose, which shows that a failed dye test is not conclusive. At that point, a leak-detection company’s pressure testing and equipment is often the most efficient route. Water loss that is much faster with the pump on or off can also help; see the pump on/off comparison.

After you find it

The complete guide to plumbing and leaks

Pool Plumbing System: Parts and How Water Flows
Read the guide

Keep exploring

Guides from other topics

All topics →