Plumbing and Leaks

How to Patch a Vinyl Pool Liner Underwater

How to patch a hole or tear in a vinyl pool liner without draining the pool: confirm the leak, prepare the patch, apply it, and know when a patch will not hold.

On this page
  1. Before you patch: confirm the hole
  2. What you need
  3. Step by step
  4. Tips for a better bond
  5. When a patch will not hold
  6. After patching: check the water level

Before you patch: confirm the hole

A patch only helps if the hole is really where the water is escaping. Before you buy a kit, confirm that the loss is not coming from the plumbing or a fitting. Run a bucket test, check the equipment pad, and use dye to locate the exact spot. Many liner leaks are at the fittings (skimmer, returns, lights, steps) where the liner is clamped, and those are not fixed by a flat patch.

What you need

  • An underwater vinyl patch kit made for pool liners. These contain pre-cut patches or patch material and an adhesive designed to cure in water. Use a product that says it can be used underwater
  • Scissors, if you need to cut the patch to size
  • A marker
  • A soft cloth or sponge to clean the area
  • Goggles or a mask, and a snorkel if the leak is deep
  • A small weight, if the kit advises it

Do not use standard PVC pipe cement or household adhesives on a liner. They are not made for flexible vinyl and may damage it.

Step by step

  1. Locate the tear and make sure you can reach it comfortably. If it is deep, consider using a mask and taking a few short dives instead of one long one.
  2. Clean the area. Gently wipe away algae, dirt or film from the liner around the tear with a soft cloth or sponge. A clean surface helps the adhesive bond.
  3. Size the patch. Cut a patch that extends at least an inch or two beyond the damage on all sides. Round the corners. Sharp corners tend to lift first.
  4. Prepare the patch and adhesive according to the kit. Some are peel-and-stick, and others have a separate adhesive that you apply to the patch.
  5. Apply the patch. Place it over the damaged area, smoothing from the centre outward so water and air are pushed out. If the tear is a slit, make sure the edges lie flat.
  6. Press and hold. Hold the patch firmly in place for the time the kit specifies. Keep your hands steady, since movement can leave a gap.
  7. Smooth the edges with your fingers, checking that all of the edge is down.
  8. Let it cure for the time stated before running the pump or disturbing the area. Avoid vacuuming or brushing near the patch during that time.

Tips for a better bond

  • Work in calm water, with the pump and cleaner off
  • Warm water usually helps adhesives work as designed. Follow the kit’s temperature advice
  • Avoid touching the adhesive side of the patch
  • If the liner is wrinkled around the tear, smooth it out first
  • Do not stretch the patch while applying it

When a patch will not hold

  • Old or brittle liners. A liner that is faded, stiff or cracked in many places may not bond reliably, and new tears may appear next to the patch.
  • Tears at fittings, seams or corners. Movement and stress in these areas pull on a patch, and a leak at a fitting may need a gasket or faceplate fix instead.
  • Large tears, or tears in the floor under load, may need professional repair or a new liner.
  • Leaks that are not in the liner, such as plumbing leaks.
  • Surfaces covered in slime or scale, which can keep the adhesive from bonding.

If the patch does not hold after one try, remove it, clean the area and try again, or consult a liner specialist. As a longer-term question, a liner with many failing areas is often a candidate for replacement.

After patching: check the water level

Over the next day or two, mark the water level and repeat the bucket test. If the loss has stopped, the patch worked. If the loss continues, the pool may have another leak, so read losing water in an inground pool. For what repairs tend to cost, see is it expensive to fix a pool leak.

The complete guide to plumbing and leaks

Pool Plumbing System: Parts and How Water Flows
Read the guide

Keep exploring

Guides from other topics

All topics →