Where pool pump leaks come from
A pump is a common place for leaks because it has several joints and a rotating shaft. The usual suspects:
- Shaft seal: where the motor shaft enters the wet end of the pump
- Strainer lid and its o-ring: a worn or poorly seated o-ring lets water out, or lets air in on the suction side
- Unions and pipe connections on the suction and discharge sides
- Drain plugs and their o-rings
- The housing: cracks from age, freezing or stress
- The seal plate or diffuser gasket, where the wet end joins the motor
Suction-side leaks often show up as air bubbles in the pump basket or at the returns, or as the pump losing prime. Discharge-side leaks show as drips or spray when the pump runs.
How to tell it’s the shaft seal
A shaft seal leak typically shows as:
- Water dripping or running from the gap between the pump housing and the motor, often at the bottom
- Drips directly below the centre of the pump, even when other joints are dry
- Rust or corrosion on the motor shaft or around the motor front
- A leak that is small or intermittent at first and gets worse over time, sometimes only when the pump is running
- A grinding or squealing noise if water has reached the motor bearings
Why it matters: the seal keeps water out of the motor. If it fails and is ignored, water can damage the motor bearings and the windings, and you may end up replacing the entire pump.
Check the easier causes first
Before you take the pump apart:
- Dry the pump and the area, then run it and watch for the first place water appears
- Inspect the lid o-ring. Remove it, clean it and check it for flattening, cracks or dryness. Lubricate it with a lubricant made for pool o-rings and reseat it
- Check unions and fittings for drips and tighten them gently by hand if the pump manufacturer recommends it
- Look at drain plugs and their o-rings
- Check the housing for cracks
If water is clearly coming from between the wet end and the motor, the shaft seal is the likely cause.
What you need
- A replacement shaft seal kit that matches your pump make and model (the model number is on the pump label)
- A new diffuser or seal plate gasket or o-ring, if your pump uses one. These are often sold with the seal or in a kit
- Basic tools, such as a screwdriver, a socket or wrench set, and a wrench or screwdriver to hold the motor shaft
- A lubricant approved for seals and o-rings, as the pump instructions direct
- Clean cloths, and your pump’s owner manual if you have it
Seal kits are typically inexpensive compared to a new pump. The labour is the main effort.
Replacing the shaft seal, step by step
Pump designs differ, so use these steps as a general guide and follow your pump manual where it differs.
- Turn off power at the circuit breaker and confirm the pump is off. Never work on a pump with power connected.
- Close the suction and return valves, or otherwise isolate the pump, and drain it using the drain plugs.
- Separate the wet end from the motor. Remove the bolts that hold the pump body to the motor or seal plate. In many designs you can leave the pump body plumbed in and pull the motor and seal plate away. Others require you to disconnect unions first.
- Remove the diffuser, if there is one, so you can reach the impeller.
- Hold the motor shaft and remove the impeller. Many motors have a slot or flats at the back of the shaft behind a cap, and you can hold the shaft there while you unscrew the impeller. Most impellers unscrew counterclockwise when you look at them from the front, but check your pump’s manual before you force it.
- Remove the old seal. The shaft seal has two parts. The spinning half, with a spring, sits on the shaft behind the impeller, and the stationary ceramic seat sits in the seal plate. Pull the spinning half off the shaft, then press or pry the ceramic seat out of the seal plate from the back, without damaging the plate.
- Clean the shaft and seal plate. Remove any scale or corrosion, and check the shaft for scoring. A badly scored or rusted shaft may mean the motor is due for replacement.
- Install the new ceramic seat. Press it squarely into the seal plate, with the polished face toward the impeller. Do not touch the polished face with oily or dirty fingers, and wipe it clean. Use a lubricant that is safe for the seal materials, and avoid petroleum-based products unless the manufacturer says they are fine.
- Install the spring half on the shaft with the carbon face toward the ceramic face, and press it into position by hand. Do not hammer it.
- Reinstall the impeller and tighten it as the manual directs.
- Replace the diffuser and the gasket or o-ring, then reattach the seal plate to the pump body, tightening bolts evenly in a cross pattern.
Reassembly and startup
- Reconnect any unions and make sure the lid o-ring is clean, lubricated and seated.
- Open the valves.
- Fill the pump basket with water and secure the lid.
- Turn the power back on, and let the pump prime.
- Watch for leaks from the seal area and the joints for several minutes, then check again after the pump has run for a while.
If it still leaks at the seal, the seal may not be seated correctly, the parts may not match the model, or the shaft or seal plate may be damaged.
Repair or replace the pump?
Consider replacing the pump if:
- The motor shaft is scored or rusted
- The motor bearings are noisy or have been wet
- The pump housing is cracked
- The pump is old and the cost of repairs is close to a new pump
- You want a more energy-efficient model, such as a variable-speed pump
If you are not comfortable working near electrical equipment, a pool technician can replace the seal for you.
Preventing seal failure
- Do not run the pump dry. Keep the water level correct, as discussed in where the water level should be on a pool skimmer
- Keep the baskets and lines clear so that the pump does not strain. See unclogging a pool line
- Keep your water chemistry in a sensible range, since harsh chemistry can wear seals and o-rings
- Inspect the pump regularly for drips, rust and noise
If the pump is dry and the pool is still losing water, the leak is elsewhere. Do a bucket test, and see the pool plumbing overview for how the pump relates to the rest of the system.