Hot Tub Care

How Water Flows Through a Hot Tub

See how water moves through a hot tub, from suction fittings and pump to filter, heater and jets, with a text diagram and notes on flow rate and capacity.

On this page
  1. The short version
  2. A text diagram
  3. The main components
  4. Circulation pump versus jet pump
  5. Flow rate and gpm
  6. How much water does a 7-person hot tub hold?
  7. If the flow seems wrong

The short version

A hot tub is a closed loop, much like a pool’s plumbing system. Water is drawn out through intake fittings, pushed through a filter and heater by a pump, and sent back into the tub through jets and return fittings. Then it does it all again. The exact layout differs by brand and model, but most spas follow the same basic path.

A text diagram

Tub water
   |
   v
Skimmer / suction fittings  --->  Filter  --->  Pump(s)  --->  Heater
                                                                  |
                                                                  v
                                       Sanitizer feed / ozone (if fitted)
                                                                  |
                                                                  v
                                   Jets and return fittings  --->  Tub water

Many spas place the filter before the pump, as above. Some designs put the heater before or after other equipment, and some use separate circuits for jets and filtration. Treat this as a general guide, and check your owner’s manual for your model.

The main components

Skimmer and suction fittings. Water leaves the tub here. A skimmer pulls in surface water, along with floating debris and oils. Suction fittings lower down do the same job from below the surface. Your filter usually sits at or behind these.

Filter. Water passes through a cartridge that traps debris before it reaches the pump and heater. A clogged filter restricts flow for the whole system. See how to clean and replace hot tub filters.

Pump. The pump moves the water. It is the heart of the system, and it needs a steady supply of water. Running it dry can damage it.

Heater. Water flows through the heater, which warms it to your set temperature. A flow sensor or pressure switch typically protects the heater, so low flow can trigger a shutdown or error message.

Sanitizer or ozone equipment. If your tub has an ozonator or UV unit, water passes through it on the way back. See non-chlorine hot tub sanitizers for what these systems do.

Jets and return fittings. Treated water re-enters the tub through the return fittings, and, when the jet pump is running, through the massage jets. Jets mix in air, which is why the water can look white or bubbly when they run.

Drain. A separate drain valve, normally closed, lets you empty the spa. See how to drain and clean a hot tub.

Circulation pump versus jet pump

Many modern spas have a small circulation pump that runs on a schedule to filter and heat the water, plus one or more larger jet pumps that you switch on for the massage. Older or simpler designs use a single pump for both. If your tub only circulates when you press the jets button, it may be a single-pump design.

Knowing which pump is which helps when you troubleshoot. See why your hot tub is not circulating water.

Flow rate and gpm

Flow rates vary a lot by design. Manufacturers measure flow in gallons per minute (gpm). Small circulation pumps are typically rated much lower than jet pumps, and jet pumps can move far more water when the jets are open. Individual jets receive only a portion of that total. Because the numbers depend on the pump, plumbing and how many jets are open, the best source is your spa’s specification sheet.

What matters for water care is turnover: how often the whole volume passes through the filter. Most owners schedule several hours of filtration per day to keep the water clean. See how to balance hot tub water for how filtration and chemistry work together.

How much water does a 7-person hot tub hold?

It varies by brand and shape. As a rough guide, larger spas that seat six to eight people often hold somewhere in the range of several hundred gallons, and smaller two-person spas hold well under that. Check the specification sheet for the exact figure. Knowing your volume is important for dosing chemicals and for working out how long to drain. See how often to change hot tub water.

If the flow seems wrong

Weak jets, no flow from the returns or heater error messages usually trace back to a few causes: a dirty filter, a low water level, closed valves, air trapped in the plumbing, or a pump problem. Start with the filter and water level, since those are the easiest to check.

The complete guide to hot tub care

How to Balance Hot Tub Water
Read the guide

Keep exploring

Guides from other topics

All topics →