Hot Tub Care

How to Drain and Clean a Hot Tub

How to drain and clean a hot tub safely, including Wellis-style drain valves, drain time, where the water can go, and what to clean the empty shell with.

On this page
  1. Before you start
  2. How to drain a hot tub, step by step
  3. How long does it take to drain?
  4. Can you drain a hot tub in the yard?
  5. How to get the last water out
  6. What to clean a hot tub with when it’s empty
  7. Refilling and rebalancing
  8. How often should you do this?

Before you start

Always switch the spa off at its breaker or disconnect before draining. Running the pump or heater without water can damage them. Read your owner’s manual too, because drain valves differ by brand and model. The steps below describe the common garden-hose drain, including the pull-out valve found on many Wellis spas.

Before draining:

  • Turn off power at the breaker or disconnect.
  • Remove the cover and set it somewhere clean.
  • Take out the filters so you can clean or replace them. See how to clean and replace hot tub filters.
  • Consider running a plumbing purge product before you drain, if you want to clear buildup from the lines. Follow the product label.

How to drain a hot tub, step by step

  1. Power off. Switch off the breaker feeding the spa.
  2. Find the drain valve. It is usually near the bottom of the cabinet, often behind a small cap or access panel.
  3. Attach a garden hose. On a typical pull-out valve, you unscrew the cap, pull the spout out to its stop, and thread a standard garden hose onto it. Use pliers gently if it sticks. Run the other end to a suitable drainage spot.
  4. Open the valve. On many pull-out designs you push the spout in partway and turn it to open. Others use a lever or a plug. Check your manual.
  5. Let gravity do the work. Water will flow until the level drops to the valve.
  6. Remove the rest. See “How to get the last water out” below.
  7. Close the valve and replace the cap before you refill.

How long does it take to drain?

It depends on spa size, hose diameter and hose length, and how far the drain is below the tub. A 400-gallon hot tub on a standard garden hose often takes somewhere around an hour or two, but that is a rough guide only. A submersible pump can speed things up considerably. Placing the hose end lower than the tub also helps the flow.

Can you drain a hot tub in the yard?

Often yes, but check first. Hot tub water contains sanitizer, and fresh sanitizer can harm lawns and plants. Local rules about where you can discharge water also vary, and some areas restrict draining into storm drains or onto a neighbor’s property.

  • Let sanitizer levels fall before draining. Letting the tub run uncovered for a few days without adding more chlorine or bromine helps. You can test the water to check.
  • Direct the water onto ground that slopes away from your house and from neighbors.
  • Avoid pointing it at garden beds, and avoid letting it pool near the tub’s base.
  • Check with your municipality about whether draining to a storm drain or sewer cleanout is allowed.

If you use a mineral or ozone system and do not add chlorine, the water is generally gentler, but the same cautions about location and local rules still apply.

How to get the last water out

Gravity usually leaves some water in the footwell, around the jets, and in the low points of the floor. To remove it:

  • Use a wet/dry vacuum to pull water from the floor and from the jet openings.
  • Use a sponge or towels for what remains.
  • Some owners tilt the hose or the vacuum to reach the lowest corner.

Do not skip this step if you will be leaving the tub empty for a while, because standing water invites mildew and biofilm.

What to clean a hot tub with when it’s empty

Use products made for spa shells, and avoid anything harsh.

  • A spa-safe surface cleaner and a soft cloth or non-abrasive sponge work for most acrylic shells.
  • Avoid household cleaners, dish soap and abrasive pads. Soap residue can cause heavy foaming later. See foamy hot tub water.
  • Clean the waterline, where oils collect, and check for slimy patches. If you suspect biofilm, see how to tell if you have biofilm in a hot tub.
  • Rinse thoroughly with clean water so no cleaner residue remains in the shell.
  • Wipe the cover and the cabinet while you are at it.

Refilling and rebalancing

Many owners refill with a garden hose, often through the filter compartment so air in the plumbing can escape. Check your manual. Once the tub is full:

  1. Turn the power back on only after the water covers the jets and the heater.
  2. Test the fill water and adjust it in order. See how to balance hot tub water.
  3. Add sanitizer, and shock if your routine calls for it.

If your fill water is very soft, see soft water and slick or gritty hot tub water.

How often should you do this?

Many manufacturers suggest roughly every three to four months for typical use, but frequency depends on tub size, how many people use it and how often. See how often to change hot tub water.

The complete guide to hot tub care

How to Balance Hot Tub Water
Read the guide

Keep exploring

Guides from other topics

All topics →