Should You Winterize an Above Ground Pool?
In regions where temperatures drop below freezing for extended periods, yes, closing an above ground pool is generally recommended. Standing water can freeze and damage the pump, filter, hoses, skimmer, and fittings, and algae or debris left to sit over winter can leave you with a green, stained pool in spring.
In mild climates, some owners keep the pool open and run the pump on a reduced schedule instead. If you are unsure, ask a local pool store what is typical for your area. For a comparison of what closing and winter care involve, see our overview of opening and closing your pool.
What You Need to Close an Above Ground Pool
Exact needs vary by pool, but a typical list is:
- Winter cover sized for your pool, with a cable and winch or other fastening system
- Air pillow (for freezing climates)
- Pool shock and winter algaecide, if you use them
- Water test kit or strips
- Chemicals to adjust pH and alkalinity
- Skimmer plate or cover, and winter plugs for return and suction ports
- Pool brush, vacuum, and skimmer net
- Cover pump for rain and melted snow
- Storage space for the pump, filter, ladder, and hoses
When to Close
Many guides suggest closing when water temperature stays below about 65°F (18°C). Closing in water that is still warm gives algae a chance to grow under the cover. Waiting too long risks freeze damage to the equipment, especially the pump and filter housing, which are not designed to withstand freezing.
Step-by-Step Instructions
1. Clean the pool
Skim, brush, and vacuum thoroughly. Anything left on the floor can become a stain by spring. Use a soft brush on vinyl liners.
2. Balance the water
Test and adjust a day or more before shocking. Commonly cited targets are pH around 7.4–7.6 and total alkalinity around 80–120 ppm. Calcium hardness recommendations for vinyl liner pools are often lower than for plaster pools, and sources vary, so follow your pool manufacturer’s guidance if you have it.
3. Shock and add winter chemicals
Add shock a few days before closing, and run the filter for at least a day afterward. Shocking a couple of days ahead rather than right before covering is often recommended to reduce the chance of bleaching a vinyl liner. A polyquat-style winter algaecide is a common addition. Follow the label for dosing, and see our article on whether you need chemicals in the pool during winter for what is essential and what is optional.
4. Clean the filter
Backwash or clean the filter according to its type: backwash a sand filter, rinse a cartridge, or hose down the DE grids. Make sure it is clean before you store or drain it.
5. Adjust the water level
Many instructions call for lowering the water a few inches below the skimmer mouth to keep water from freezing in the skimmer. However, some above ground manufacturers say to leave the water at its normal level, and others say to follow the cover maker’s instructions. Check your owner’s manual. Do not drain an above ground pool completely. Pool walls rely on the water for support, and an empty pool can be damaged or collapse in wind.
6. Drain and store the equipment
Disconnect the hoses, pump, and filter. Remove drain plugs, drain each unit fully, and store them indoors (a garage, basement, or shed). Keep small parts like gaskets, plugs, and baskets together in a labeled bag.
7. Plug lines and protect the skimmer
Remove the return fitting and seal the return and suction ports with winter plugs. Install a skimmer plate, guard, or expansion device if your system uses one.
8. Add the air pillow
In freezing climates, an air pillow floats under the cover and helps absorb pressure from ice. Instructions vary on how much to inflate it, and many manufacturers say to leave it only partially inflated. Follow the instructions that came with yours.
9. Install the cover
Spread the winter cover over the pool, then secure it with the cable and winch around the perimeter. Cover clips can help stop wind from lifting the edges. A cover that is loose or sagging can let in debris and water.
10. Add a cover pump
Rain and snowmelt can build up on the cover and overload it. A small cover pump removes water automatically. Place it where water collects, and keep the cord and hose clear. In spring, you will need to deal with whatever has collected, as covered in our guide to removing a winter pool cover without dumping debris in the water.
Common Mistakes
- Draining the pool entirely. This can damage the liner and walls.
- Leaving the pump and filter outdoors with water inside. Freezing can crack the housings.
- Skipping the top rail and upright inspection. Rust or damage is easier to address before winter than after.
- Closing too early in warm water. Algae can bloom under the cover.
- Storing the ladder and rails outside. Moisture and cold can corrode some metal parts.
Taking Down and Storing an Above Ground Pool
If you plan to dismantle the pool entirely instead of closing it, the process is more involved: drain the pool, remove the liner, and take apart the frame. Manufacturers publish specific instructions, and the steps differ between soft-sided, steel-wall, and resin-wall pools. Check your manual. Roughly speaking:
- Drain the water in a way that is legal and safe for your area. Check local rules about where pool water can go.
- Clean and dry the liner and any removable parts completely before folding to avoid mold.
- Store the liner, frame parts, and equipment in a dry, sheltered place away from rodents.
- Keep hardware organized and labeled so reassembly is easier.
Related Reading
When spring arrives, see when to open your pool for timing guidance.