Saltwater Pools

How to Convert a Chlorine Pool to Saltwater, Step by Step

Convert a chlorine pool to saltwater in five steps: balance the water, size and install the generator, add salt, start it up and tune the output.

On this page
  1. Before you start: is your pool a good candidate?
  2. What you need
  3. Step 1: Balance the water
  4. Step 2: Choose and size the generator
  5. Step 3: Install the cell and control box
  6. Step 4: Add the salt
  7. Step 5: Start up and set output
  8. After the conversion
  9. Common mistakes

Before you start: is your pool a good candidate?

Most pools can be converted without draining, but it is worth checking a few things first.

  • Materials. Vinyl, fiberglass and well-sealed plaster pools are commonly converted. Salt can damage some natural stone and corrode certain metals, so check coping, decking, ladders, lights and the heater against the manufacturer’s guidance. Our article on sacrificial anodes covers one corrosion safeguard.
  • New plaster. If the pool was recently resurfaced, ask the builder how long to wait before adding salt.
  • Warranty. Check your pool, liner and equipment warranties for salt restrictions.
  • Budget. Conversion costs are commonly quoted in the range of a couple of thousand dollars, but vary by system and installation. See whether saltwater pools cost more to maintain to understand the long-term picture.

What you need

  • A salt chlorine generator (control unit, cell and flow switch).
  • Pool-grade salt, see what is the best salt for your pool.
  • PVC fittings and tools for the plumbing, or a professional installer.
  • A qualified electrician for wiring if you are not experienced with it.
  • Test kits for pH, alkalinity, calcium hardness, stabilizer, free chlorine and salt.

Step 1: Balance the water

Test and adjust before adding any salt. Common targets are pH 7.2 to 7.6, total alkalinity 80 to 120 ppm and calcium hardness 200 to 400 ppm. Keep cyanuric acid within the range your generator’s maker recommends. Starting balanced reduces the chance of scale on the new cell. Also check for metals such as copper or iron, which can stain once the chemistry changes.

Step 2: Choose and size the generator

Generators are rated by pool volume in gallons. Many installers recommend choosing a model rated above your actual volume, which lets the cell run at lower output and can help it last longer. Get your volume right, since it determines both the generator size and the salt you will need. For above ground pools, see choosing a salt water system for an above ground pool.

Step 3: Install the cell and control box

The cell goes in the return line after the filter and after any heater or other equipment, so that it is the last item before water returns to the pool. Manufacturers usually specify a straight section of pipe near the flow switch and cell. Follow the installation manual.

The control unit needs power, and it should be wired so that it only operates while the pump is running. This prevents the cell from producing gas in stagnant water. Electrical work around pools carries a risk of shock, so use a licensed electrician if you are not certain how to do it safely, and make sure any required grounding and bonding is in place. Check for leaks when the system is first pressurized.

Step 4: Add the salt

Work out how much you need with our guide to how much salt to add to a pool. With the generator off and the pump running, pour the salt around the pool, particularly in shallow areas. Brush it to help it dissolve. Run the pump for roughly 24 hours, longer if needed, then test the salt level with a reliable method. Add more only if it is below target. If you overshoot, see is 4000 ppm salt too high.

Step 5: Start up and set output

Once the salt has dissolved and the level is in range, turn on the generator. Many people start at a moderate output setting, then test free chlorine and adjust output up or down in small steps over a few days until chlorine holds at the level you want. If chlorine will not rise, see salt chlorinator not producing chlorine.

After the conversion

Common mistakes

  • Guessing the pool volume, which leads to too much or too little salt.
  • Running the generator while salt is still dissolving.
  • Skipping the water balance, which causes scaling.
  • Using the wrong salt or adding it directly into the skimmer.
  • Neglecting to check metal fixtures and other equipment for salt compatibility.

The complete guide to saltwater pools

Saltwater Pool Care: Salt, pH and Shock
Read the guide

Keep exploring

Guides from other topics

All topics →